Apply a waterproofing sealer to the cooler pan with a disposable brush. Use the product as recommended by the manufacturer. Apply an exterior grade enamel to any bare metal areas remaining on the outside of the cooler and panels. Allow the repairs to dry thoroughly before returning the cooler to service.
Does Flex Seal work on swamp coolers?
I have used it and a similar product bought from the Big Box stores and for me it worked great, the Ranch swamp cooler bottom was completely rusted gone and the flex seal filled the gaps and it does not leak at all , so for me it worked.
How do you weatherproof a swamp cooler?
- Turn Power Off. First, turn the power supply off on your unit. ...
- Turn Water Supply Valve Off. In order to keep the pads inside of the unit wet, the cooler needs a water supply valve to bring water into the unit. ...
- Drain the Swamp Cooler. ...
- Cover the Unit.
How do I prevent mold in my swamp cooler?
To prevent mold growth, you need to keep the moisture level under control . In many cases, you can leave another window open to reduce the overall humidity in the evaporative cooler and air. A HEPA air cleaner can clean the air if you do get mold in the unit. You'll need to clean it before operating it again.
Why is water leaking from my swamp cooler?
Swamp coolers function by running water over pads that water is forced through in order to cool it off . ... Condensation and too much water in the system will lead to a drip. This overflow is normal! If it happens occasionally, it just means there's a little more water in the air conditioner than normal and it'll equalize.
How do you turn a swamp cooler on in the summer?
Swamp cooler controls will have an on/off switch that controls the water pump and fan hi/low button . When you turn it on it will begin pumping water through the cooler and then you can adjust the fan speed to high or low. You need to have the pump on while running the cooler, to keep water running through the unit.
How long does it take for cooler coating to dry?
Cure Time Guideline: Coating cure time is dependent upon a number of conditions (temperature, humidity level, etc.), but mainly the coating thickness. The thicker the coating the longer the cure time. Typically, properly applied coating should cure within 24 to 48 hours .
Can I run my swamp cooler all day?
You can run your swamp cooler all day should you so choose without seriously increasing your monthly utility bill. However, you will need to be available to refill the reservoir in the interim. Should you not want to do that, run your swamp cooler first thing in the morning or overnight to fill your home with cool air.
How much does it cost to winterize a swamp cooler?
Cost to Winterize a Swamp Cooler
Winterizing a swamp cooler will cost about $100 to $150 , not including parts. This will save you maintenance during the following summer, extend the life of the unit, and will include: Draining the unit.
When should you winterize your swamp cooler?
Typically, you should start thinking about turning off your swamp cooler and turning on your furnace when the nights drop below 50° and days are in the low 70°'s .
Can I use vinegar in my swamp cooler?
Clean . Add a cup of vinegar to the cooler pan and let the vinegar cycle through the system for up to an hour. This will eliminate odors, mold, mildew and some corrosion, calcium deposits and other types of build-up.
Can swamp coolers cause respiratory problems?
But worse, breathe bad air in constantly and it can eventually lead to respiratory problems like allergies or asthma . Another problem with swamp coolers as it relates to cleanliness is that moisture in the ductwork causes it to break down over time, pushing metal particles out of the vents and into your home.
Can I put bleach in my swamp cooler?
Completely drain the evaporative cooler and refill with a mixture of fresh water and household bleach (that has 4% available chlorine). Allow 5 millilitres of bleach for every 5 litres of water . ... Do not exceed this concentration or the evaporative cooler could be damaged.
Can I run my swamp cooler without the pump on?
Yes, the fan and pump motors are separate systems. You can run one without the other with no damage to the product . That said, however, you will not receive the same degree of cooling by only running the fan.
How do I fix a leaky swamp cooler pan?
Apply a waterproofing sealer to the cooler pan with a disposable brush. Use the product as recommended by the manufacturer. Apply an exterior grade enamel to any bare metal areas remaining on the outside of the cooler and panels. Allow the repairs to dry thoroughly before returning the cooler to service.
What to do if swamp cooler is leaking?
Inspect the drain hole on the bottom of the cooler for leaks. If you see water leaking, check to see that the overflow pipe is screwed securely into place in the drain hole. Tighten the overflow pipe. If that doesn't work, you may need to replace the drain fittings and/or the overflow pipe.
