FOX’s shocks are ‘serviceable’ – meaning each shock can be rebuilt with new internals , and a new nitrogen gas charge can be applied to the shock, complete ride refreshment.
How much does it cost to rebuild a FOX shock?
| REBUILD REVALVE | OEM Raptor Front w/Coil $125 $35 | 2.5 Bypass 2.5 Internal Bypass 3.0 Bypass XP 1000 Front $150 $35 | 3.0 Internal Bypass 3.5 Bypass XP 1000 Rear $250 $35 | 4.0 Bypass $300 $35 |
|---|
Do FOX shocks need a rebuilt?
A complete shock rebuild is recommended every 1,000 miles for off-road race applications . Split street/off-road–use vehicles every 10,000 miles, and street every 50,000 miles. A FOX complete shock rebuild service includes new seal kit, new proprietary JM92 Suspension Fluid, deburr and polishing of shock shafts.
How do you rebuild Polaris FOX shocks?
How many miles do FOX shocks last?
About 50k miles of normal driving . Any shop that rebuilds shocks can rebuild them for a whole lot cheaper than new ones. Darn, 50k seems a bit low. I’ll have to research shops in my are that could do it when the time comes.
Are FOX shocks lifetime warranty?
Warranty Policy. The factory warranty period for your fork/shock is one year (two years for countries in the EU) from the original date of purchase of the bicycle or fork/shock . A copy of the original purchase receipt must accompany any fork/shock being considered for warranty service.
Can shocks be rebuilt?
Not every shock absorber problems can be repaired . Parts that you can replace individually include mounts, shock absorber bushings, seals, piston, and compression oil. As a rule of thumb, you should only consider shock absorber repair if the existing shocks have not done more than 35 000 miles or slightly more.
How do you maintain FOX shocks?
To extend the service life of your FOX fork or shock, the best product maintenance plan you can follow is cleaning the product exterior after each and every ride or race . Use mild soapy water, a very light pressure water spray to rinse, and wipe dry with a clean, dry cloth.
How often should FOX shocks be serviced?
Fox recommends that the minimum suspension fork and shock service is 125 hours of use, yearly, or whichever comes first . That is certainly on the longer side of things. Similar to changing the oil in your car, the more frequently you service your suspension, the better the fork will perform for longer.
How do I know if my shocks need to be rebuilt?
Are FOX shocks good?
FOX Jeep shocks are made of aluminum because 6061 aluminum’s thermal conductivity value is over four times that of low carbon steel. This means that aluminum FOX shocks are able to cool much better than painted steel shocks, and they are extremely resistant to rust .
Can you add reservoir to FOX shocks?
Fox 2.0 Remote Reservoir Performance Advantage
Adding Remote Reservoirs to Fox 2.0 Performance Series Shocks improves their ride quality, long term durability and heat capacity . Remote reservoirs reduce the operating gas pressure, friction and heat inside the shock by allowing more volume for the nitrogen to expand.
How do you rebuild shocks?
How much oil does a Fox shock take?
| Oil Location Application Oil Volume | Air-Side Bath All 32mm FLOAT 130-150 Air-Side Bath 10cc | Air Chamber All FLOAT NA2 and RHYTHM Air Chamber 3cc | Damper-Side Bath All 32mm FIT4 Damper-Side Bath 15cc | 32mm Grip Damper-Side Bath 40cc |
|---|
Is Bilstein better than Fox?
Bilstein 5100 has lifted vehicle support too, and they function well right until you get to the 4” mark. Above that, Fox is the king . 2.0 shocks will provide firmer control and better damping on higher lifted trucks. The fit is also snugglier if you decide to go big with 4.5” or 5”+ lifts on your offroad monster.
What’s better fox or King shocks?
Fox oil offers substantially better lubrication across a wide range of temperatures based on the manufacturer ratings. Viscosity index (VI) is a measure of how much the damping will fade due to heat. Fox’s VI of 370 is very high and provides exceptional performance. King’s VI of 150 is an average rating.
How much does it cost to rebuild King shocks?
King Shock Rebuild Request
Average cost is around $600-$700/set of shocks assuming no substantial parts are needed (reservoir assembly, shafts, etc.). It’s not uncommon to need rear shafts on shocks that have been neglected but 90% of our rebuilds are seals, oil and a couple bearings.
Are Fox shocks good for towing?
The Fox Performance Series 2.0 IFP is constructed with a monotube design and an internal floating piston. The result is a solid performance and reliable damping in the harshest driving conditions, specifically when towing or off-roading .
Where are Fox truck shocks made?
Fox are made in the USA and are built to the highest technical specifications. They are derived from the technology Fox have developed over 30/40 years of off road racing.
How do you fix a blown shock?
How much does it cost to get new shocks?
Shock Replacement Cost
The average total cost to replace a pair of shocks will run about $250 to $580 . An individual shock absorber will cost around $50 to $140 so parts alone will set you back between $100 and $280. A couple hours of labor to do the job is an additional $150 to $300.
How do I know if my shocks are blown?
- Instability at highway speeds. ...
- Vehicle “tips” to one side in turns. ...
- The front end dives more than expected during hard braking. ...
- Rear-end squat during acceleration. ...
- Tires bouncing excessively. ...
- Unusual tire wear. ...
- Leaking fluid on the exterior of shocks or struts.
How do you rebuild a FOX Float rear shock?
How do you add nitrogen to FOX shocks?
How do you fill a FOX Float shock?
Check that no part of your shock contacts any portion of your frame or linkage as it cycles through its travel. Add air pressure to the main air chamber in ~50 psi (3.4 bar) increments, slowly cycling the shock after every 50 psi (3.4 bar) addition .
