The torque specifications for GM wheel hubs generally range between 107 to 225 foot-pounds , depending on the year and model.
How much torque should a hub bearing have?
with no more than 15 to 20 ft. lbs. of torque while rotating the wheel to make sure the bearings are seated.
How tight should a hub bolt be?
The nut on the spindle should be tightened until snug , with no side-to-side play in the hub and then backed off, about a quarter of a turn. The nut finger should be tight until the castle nut or cotter pin is used.
What is the torque specs for a axle nut?
For a double nut or jam nut system, bend the lock tab or install the set screw after the outer nut is torqued to 200 ft-lbs. For one-piece spindle nut systems, torque the nut to a minimum of 300 ft-lbs.
What is the torque for a front axle nut?
Generally, jam nuts less than 2-5/8′′ should be torqued to 200-300 lbf-ft; nuts 2-5/8′′ and over should be torqued to 250-400 lbf-ft . See chart for exact torque specification.
Can you over tighten wheel bearings?
“Excessive preload will cause excessive friction and the bearing will run hot, compromising lubrication and eventually leading to flaking (material coming off) at the large end of the rollers/races,” he says. “On the other hand, adjusting the bearing too loose causes excessive looseness and vibration in the system.
What size socket do I need to remove a wheel bearing?
It’s a 4 MM !
What happens if you over tighten axle nut?
It’s possible to damage the wheel, rotor, and hub assembly . The wheel can come off if over-torquing the nuts/bolts is done.
What should I torque my wheels to?
| Hardware Bolt or Stud Size Typical Torque Range in Ft/Lbs Minimum Number of Turns of Hardware Engagement | 14 x 1.25 mm 85 – 90 9 | 7/16 in. 70 – 80 9 | 1/2 in. 75 – 85 8 | 9/16 in. 135 – 145 8 |
|---|
What are signs of bad wheel bearings?
- Humming Noise. The most easily identifiable and most common symptom of bad wheel bearings is an audible one. ...
- Squealing, Growling. ...
- Clicking Sound. ...
- Wheel Wobble. ...
- ABS Failure. ...
- Uneven Tire Wear. ...
- Vehicle Pulls to One Side. ...
- Steering Wheel Vibration.
Do you need to torque axle nut?
Proper torque is critical for two reasons. First, it secures the axle nut so it won’t work itself loose and back off . Second, the proper torque keeps the correct load on a hub assembly needed for longer bearing life. ... When you’re removing the wheel hub nut, you can use an impact wrench to speed up the job.
What is the torque spec?
Recommended torque specifications are unique for each type of vehicle. ... By definition, torque refers to the amount of rotational force at the point of application . When attaching a wheel to a vehicle, torque specifications are the amount of force recommended on the hardware to ensure proper installation.
How do you torque a wheel hub nut?
Lubricate the wheel bearing with clean lubricant of the same type used in the axle sump or hub assembly. Tighten the adjusting nut to a torque of 200 ft-lb while rotating the wheel hub assembly . Back the adjusting nut off one full turn. Re-torque adjusting nut to 50 ft-lb while rotating the wheel hub assembly.
How tight do you tighten front wheel bearings?
The nut on the spindle should be tightened until snug , with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.
What are the most common axle nut sizes?
| Item No. Description Weight | 30410 3.25′′ 8 pt. Axle Nut Socket 2.7 lbs (1.2 kg) | 30411 3.5′′ 6 pt. Axle Nut Socket 2.95 lbs (1.3 kg) | 30412 3.75′′ 8 pt. Axle Nut Socket 3.15 lbs (1.4 kg) | 30413 4′′ 6 pt. Axle Nut Socket 3.35 lbs (1.5 kg) |
|---|
