Life Member.
Yes, you can move your PCV to the other bike as both bikes use the same one
(Part # 15-011).
What can you do with a Power Commander?
The Power Commander V is a unique EFI tuning device because it can
monitor and maintain your air/fuel ratio without directly changing the ECU
. To reinstate your stock settings, all you need to do is uninstall the device, and you’re done.
Does Power Commander 5 marry to bike?
Registered. Power Commander is
not “married” to a bike
.
Can you put a Power Commander on a stock bike?
Registered.
yes it’s worth the extra money especially if you get the ignition controller too
. tuning a stock bike to run on 91 octane will always make power over stock.
How do I Unmarry my Dynojet Power Vision 3?
Click the Tools tab, then click Unmarry PV3 from the top menu ribbon bar. Then click on the Get Unlock Info button. Copy the entire Unlock Seed Code and reply to this email with that Seed Code. We will then email you back a Key – paste that into the bottom section, then click Unmarry.
Is Power Vision married to bike?
The Power Vision, by default has the ability to tune one bike.
Once it is married to a specific bike, it cannot be used to tune another bike
. However, a license can be purchased allowing the Power Vision to tune another bike. There are three license options available, Unlock, Dual, and shop Tune license.
Can I use a Power Commander on a different bike?
Life Member.
Yes, you can move your PCV to the other bike as both bikes use the same one
(Part # 15-011). You will however need to go to the Power Commander website and download a new map to the PCV that matches your current setup for the 2012.
How do I reset my power commander?
To reset the throttle position
click on “Power Commander Tools” and then select “Set Throttle Position
. To reset both the closed and open throttle positions, first make sure that the bike is communicating to the computer, then click on “Reset”. Twist the throttle wide open and release. Now click OK.
Are power commanders worth it?
How much horsepower will a Power Commander add?
The Power Commander is a tuning tool to adjust fuel, and on some models ignition timing. Just adding a Power Commander to a completely stock vehicle
usually does not increase peak horsepower
. It usually will improve drivability, throttle response, and mid-range horsepower and torque.
Do you need to dyno tune a Power Commander?
yes you need a powercommander for a dyno tune
. That is what they tune that controls how much fuel is pumped into your engine. You also should install block off plates. It may help with some of the popping as well.
Can a Power Commander hurt a motorcycle?
Registered.
Power Commanders do not harm your bike
. They don’t “trick” the OEM ECU. It is nothing more than a piggyback ECU.
Can you Unmarry dynojet?
You must contact Dynojet Research first to pay for the unlock license and to obtain the unlock code
. This is a bit of a process as once you start this process you need to keep the PVCX connected to the computer and software open the entire time.
How do I unlock Dynojet Power Vision?
- Plug in the USB cable into the Power Vision.
- After the Power Vision boots up and says “PC Link Mode Active”.
- Launch the WinPV Software.
- On the menu bar, go to “Power Vision”, and choose “PV Info”.
- Copy the text displayed in the window.
- Purchase the Unlock License using the ‘Add to Cart’ button above.
How do you unlock power vision?
Is the Dynojet Power Vision waterproof?
The Power Vision is weather resistant
. We recommend removing the Power Vision before washing the motorcycle.
How does a Power Vision license work?
Through a Tune License, you can unlock the true potential of your Dynojet Power Vision. Your Power Vision will be able to tune the original motorcycle, as well as one additional Harley.
Your Power Vision device will remember each license that is applied, essentially multiplying the power of your device
.
How do I adjust my Power Commander 2?
Will a Power Commander lose its map?
If you disconnect the battery or disconnect the Power Commander from the bike it will not lose the map
. The only way to lose the map is to download another map to the unit.
