How Do You Remove A Pulley From A Keyed Shaft?

To tighten the screw at the end of the gear puller,

use the sockets wrench

. Continue until the pulley is free. You can try to loosen the pulley by hitting the exposed end with a hammer.

How do you get a stuck pulley off a water pump?

1. Remove obstacles away from the water pump. …
2. Remove the engine’s timing belt or chain if necessary, as this is often in the way of the water pump. …
3. Remove the water pump belt from the water pump. …
4. Install the pulley removal tool to the water pump pulley. …
5. Tighten the removal tool slowly.

Why is my water pump pulley not spinning?

In most cases,

the water pump is binding up, causing the pulley to stop spinning

. Replacement of the water pump will fix your problem. The pulley will need to be replaced if there is damage from the belt on it. If there is no damage, then the pulley can be reused.

Can you Unseize a water pump?

Seized pumps can be freed by applying penetrating fluid such as ‘

WD

-40′, or ‘PB Blaster.

What tool removes a broken water pump bolt from engine block?

Once you have been able to get the right

extractor

, removing the hardened broken bolt will be easy after you’ve got a hole on the fastener’s center point. Use the extractor tool to unscrew the fastener gently, and it should come off quickly without much effort.

How is a crankshaft pulley removal?

1. Position the puller in front of the pulley. …
2. Install the puller-to-pulley bolts. …
3. Using a breaker bar and socket, tighten the central puller bolt until the pulley slides off the crankshaft.

Should a power steering pump spin freely?

If there is no drive belt on the pulley that is on the power steering pump, you should be

able

to turn the power steering pump pulley freely and easily by hand. If the pulley (shaft) does not turn, that means that something within the power steering pump has broken or seized.

How do you know if your water pump is frozen?

Look for any visible frost on the exterior of the pipes or the pump

. This will help you determine if the freeze occurred before, at, or after the actual pump.

Should my water pump spin freely?

The pump doesn’t have the same kind of bearings as, say, an alternator, and some resistance is normal. As long as the shaft doesn’t get hung up on anything and doesn’t feel gritty when you rotate it, it’s

fine

.

How do you get a broken bolt out of an engine block?

The traditional method includes

taking a punch and creating a divot (or center point) on the broken bolt

surface, drilling a pilot hole freehand, hammering in an easy out extractor, then attempting to back the bolt out.

How do you remove a pulley from a deck?

1. Remove the mower deck from the lawn tractor. …
2. Remove the bolt from the center of the pulley with a wrench. …
3. Place the three jaws of the spindle puller under the pulley and center the threaded screw directly in the center of the pulley so it rests on the spindle shaft.

Which tool is used to remove the crankshaft pulley?

A half-inch drive impact gun

might be a great tool for removing a stubborn crankshaft pulley bolt. A torque wrench has also been proven to be a helpful tool for correctly securing it.

How much is a pulley puller?

Which way do crank bolts undo?

Remove crank bolt or nut by turning

counter-clockwise

. If no bolt is visible, remove dust caps. Some caps pry out and some thread out.

How do you loosen a tight crankshaft pulley bolt?

1. Soak in Lubricant. Although the bolt sits on the side of the engine, you can use putty to create a sticky dish for your lubricant of choice. …
2. Rent A Powerful Impact. …
3. Try a Long Breaker Bar. …
4. Bump the Starter. …
5. Take It To A Shop.

How do you remove a harmonic balancer pulley without a puller?

Most vehicle engines are now equipped with a pulley that holds the harmonic balancer apart from the center bolt. To remove the pulley, you need to

rotate it a little with a screw driver’s help and pull it out using a pickle fork

.

What causes crankshaft pulley to break?

Another way a pulley can fail is during the fitting process there has been

an interruption with the assembly press

or the friction bearing has been incorrectly pressed in. This can occur during the making and installation of the part with the vehicle.

Should a power steering pump pulley move in and out?

The pulley shaft will commonly move

in and out of pump body

even on brand new units, I’ve seen 1/8′′ before. Normal.

Does the crankshaft pulley move?

The camshaft and crankshaft pulleys are directly attached to the engine (camshaft and crankshaft) and

will only rotate if the engine is running

or manually rotating the engine by placing a socket and breaker bar to the crankshaft pulley bolt.

How do you know if your power steering pulley is bad?

1. Burning smell from engine. A burning smell from the engine means the belt is not tight enough or the power steering pump pulley has seized. …
2. Choppy steering. …
3. Steering fails completely.

Can power steering pump seized?

The power steering

pump will overheat and seize up

. When this happens, the belt will very quickly wear out by being dragged across a stationary pulley. Eventually it will snap or shred.