While a chain saw does
produce some heat while in use
, it should never overheat or begin smoking. … The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.
What causes white smoke from a chainsaw?
The main reason for a chainsaw that emits smoke (white most of the time), is the result of
a bad oil / fuel mixture or bad oil
. … Be careful, white smoke from bad mixing will cause further breakdowns and damage the entire mechanism.
Why do chainsaws overheat?
Chainsaw engines run
at high temperatures
, usually in the summer, so they can quickly overheat. … The cylinder and starter both contain air intake areas that pull cool outside air into the engine when it's running. If dust, wood chips or other material blocks these systems, the engine will start to overheat.
Why is my chainsaw burning the wood?
If the oil pump for the bar oil is not pumping oil on to the bar it will cause the chain and the bar to get very hot
. If this is happening, it may cause the wood to burn. The only other thing I can come up with is the chain may be very dull or on backwards.
How tight should my chainsaw chain be?
Good Tension-
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be
tight enough that you can't pull the drive links out of the bar nose
.
Should a new chainsaw smoke?
While a chain saw does produce some heat while in use,
it should never overheat or begin smoking
. … The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.
Why is my chainsaw smoking and not cutting?
This most commonly is a result of
a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut
. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Is it normal for a chainsaw bar to get hot?
Yes they do get hot more so when the full length of the bar is being used
. Over tightening the chain and dull cutters will make it worse. When you hit a something stop & sharpen or switch chains.
Is it normal for chainsaw to get hot?
It is normal for the blade of your chainsaw to produce some heat
. But it should not overheat or smoke. If you notice any overheating or smoke coming out of the blade, you should stop its use at once.
Will burnt wood dull a chainsaw?
Cutting burned trees is
extremely demanding
on a chain saw. It is very abrasive and fine particles. Check the air filter often. It will need cleaning or replacing on a regular basis.
Is it bad for a chainsaw to cut wet wood?
Does this pose any risk to your chainsaw? In all honesty, no!
The additional moisture found on wet wood will not make any difference to the cutting process
. It doesn't place any additional resistance on the chainsaw, and no additional effort is required to cut through it.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw
once after you have gone through three chains on the same bar
.
When should you throw away a chainsaw chain?
Chainsaw feels unbalanced, cuts
unevenly
, or rattles when in use. In short, if you have attempted to balance your cutting teeth, are certain of your depth gauge, and the tension is properly adjusted, but the saw still doesn't cut correctly- then you need to replace the chain.
How long should a chainsaw bar last?
Re: how long does a bar last
The next, a Granberg, lasted
about 2 months
. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
How long does a chainsaw last?
That being said, you can expect a quality chainsaw to last you
at least 10 years or more
. But if you take care of it, I know people who have saws that have lasted 20-30 years and even longer.
Why does my chainsaw chain dull so quickly?
If your chain dulls quickly, then it could be a couple of things. Check your user's manual to ensure that you are using the right sized file for your chain. Alternatively, you could be
applying too much pressure when you file
. This will create cutting edges that are too thin and dull quickly.
Can you over tighten a chainsaw chain?
After a few hours of use, a chainsaw's chain can loosen and begin to sag away from the bar. … There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise.
Don't over-tighten the chain
as this could cause it to break.
Can chainsaw air filters be cleaned?
Step-By-Step Chainsaw Air Filter Cleaning Process
Remove cylinder cover. Remove the air filter. Give the air filter a once over, looking for any external dirt build-up, damage or wear. If there is a lot of dirt, wash the filter with a soft brush in warm soapy water and rinse until the water runs clear.
Why is my chainsaw leaking bar oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar,
air begins to replace the space where the oil was previously stored
. If there isn't proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
Can Stihl air filters be cleaned?
What's more, HD2
air filters can be easily cleaned and reused multiple times
: just spray the removed filter with STIHL Varioclean, leave the detergent to take effect briefly, then rinse and dry the air filter before reinstalling it. Watch to learn how to clean your air filter at home.
Can you clean a chainsaw fuel filter?
Usually,
you don't clean the chainsaw fuel filter
. They are extremely cheap, so you don't have a reason to do it, just change them. You won't be able to do this on all fuel filters, but on those you can, this is the only way to do it without changing them.
What are the rakers on a chainsaw chain?
Depth gauges, “riders,” or “rakers,” as they are sometimes called,
control the amount of wood severed by a cutter tooth
. During the life of a pro saw chain, they occasionally need maintenance for top cutting performance.
Why does paint come off chainsaw bar?
Chain is too tight and wearing one side of the bar down more than the other
.
Should you run a chainsaw at full throttle?
Generally,
two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown
. Therefore, running at any throttle speed below the full throttle is not advised. Cutting a thick wood or timber while running at a low speed or throttle can cause the blades of the chainsaw to become dull.
What happens if you run a chainsaw without bar oil?
No bar oil equals increased friction and heat
. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Can you chainsaw frozen wood?
Just plain old wet frozen wood
won
‘t dull a chain . It will however make even the largest saw cut like the chain is on backwards .
