How Much Oil Does A Mercury Outboard Take?

by | Last updated on January 24, 2024

, , , ,

Remove the filler cap from the back of the powerhead, then fill the outboard with

3 quarts

of Mercury 4-stroke marine engine oil and replace the filler cap.

Contents hide

How much oil does a 90 HP Mercury 4-stroke take?

Model US Crankcase Capacity 90 FourStroke Carbureted

5.28 QT.

(169 oz.)
90 FourStroke EFI, 1596cc, 1B366822 & below 4.80 QT. (160 oz.) 90 FourStroke EFI, 1731cc, 1B366823-28094995 5.28 QT. (169 oz.) 90 FourStroke 2B094996 and above 5.5 QT. (176 oz.)

How much oil does a Mercury 150 take?

Another qt of oil needs to be added to this oil change kit to complete an oil change in a Mercury 2019 Pro XS 150 that has a

6.3 qt

capacity.

What kind of oil does a Mercury 4-stroke take?


Synthetic Blend 4-Stroke (25W-40) Outboard Oil

Mercury 25W-40 Synthetic Blend Outboard Oil meets the stringent marine operational requirements of all of Mercury's new 4 and 6 cylinder models.

What type of oil goes in a Mercury 150 lower unit?


Mercury Premium SAE 80W90 Gear Lube

is recommended for lower units for outboards below 75 horsepower. Mercury Premium SAE 80W90 Gear Lube should not be mixed with Mercury High-Performance SAE 90 Gear Lube.

How much oil does a Mercury 4 stroke take?

Remove the filler cap from the back of the powerhead, then fill the outboard with

3 quarts

of Mercury 4-stroke marine engine oil and replace the filler cap.

How much oil does a 20 hp Mercury outboard take?

PRO TIP: The Mercury 20HP outboard engine takes

1.1 quarts of oil

, so add 1 quart, replace the cap, and run the engine for a couple of minutes. When you run it, be sure to have water circulating through the engine as you would when you flush the engine out after use.

How often should you change oil in a 4 stroke outboard?

The maintenance schedule for most four-stroke outboards calls for an oil and oil filter change

every 100 hours, or annually

. If you put your boat up for the winter, professional technicians suggest changing the oil as part of preparation for off-season storage.

How much oil does an outboard lower unit hold?

Lower Unit Oil Needed by Model Model Approximate Fluid Ounces Required 15B & C (4-stroke)

12.5 fl oz
18 (2-stroke & 4-stroke) 12.5 fl oz 20 (4-stroke) 12.5 fl oz

How often should I change my lower unit oil?

Most sterndrive and outboard manufacturers advise you to change the gearcase oil in your lower unit

every 100 hours or once a year

(whichever comes first). Clean oil is critical for protecting the heavily loaded gears in your lower unit and preventing expensive damage.

Is Quicksilver oil made by Mercury?


Quicksilver oil is repackaged Mercury Oil

for other retail sales outlets,a few years ago I called mecury to ask if they were the same oil and was told they couldn't or wouldn't say so. but the guy said he would use QS premium plus over the regular Merc oil.

How often should boat oil be changed?

Change the engine oil at

least once every season

. Refer to your engine owner's manual for the manufacturer's oil change recommendations. Before every voyage, take a minute to inspect all belts and hoses; replace any that are torn or show signs of excessive wear.

Should I use synthetic oil in my Mercury outboard?

It is recommended for most Mercury Racing four-stroke engines and Verado outboards offered before the 2007 model year.

Synthetic Blend 4-Stroke (10W-30)

Outboard Oil is designed to meet the needs of all four-stroke outboard motors, with industry-leading corrosion protection.

Can I use regular gear oil in my lower unit?

So, can you use any old gear lube in your marine lower unit? If you want the best protection possible, and want your lower unit to last as long as your boat, then the answer is no.

Consult your engine's manual and look for

the proper marine gear lube for your application.

Can you overfill lower unit oil?

To answer,

yes you can

. I have seen guys that will pump it till the oil comes out the top which is correct, but will then put the top screw in & then give a few more pumps for “good measure”. This usually causes overfilling as well as a slight pressurizing if they get that bottom screw in real fast.

What does Milky lower unit oil mean?

Milky oil means

water has gotten into the lower unit

. It is usually a bad propshaft seal, rather than a waterpump seal. But it is a job for your local shop. They'll replace the seals and pressure check the lower unit. They'll also be able to tell you if anything more than seals is required.

How much oil does a Mercury 115 Pro XS take?

HP / kW 115 / 86 Exhaust system Through prop Color Phantom Black Lubrication system Wet sump Oil Capacity

5.5 qts / 5.2 l

How many hours can you get out of a 4 stroke outboard?

A typical two-stroke or four-stroke outboard engine should provide

1,500 hours

of run time. Based on the average use of 200 hours per year, this will last 7-8 years. However, changing your oil every 50 hours of operation and regularly flushing the engine can see your outboard engine last 10 to 20 years.

When should I change the oil in my Mercury 4 stroke outboard?

The maintenance schedule for the Mercury 150 FourStroke, and for most four-stroke outboards, calls for changing the oil and the oil filter

every 100 hours

, or annually. For many boat owners this annual oil change is part of preparing the outboard off-season storage.

What kind of oil does a 9.9 Mercury 4 stroke take?


10W30

is recommended for all . Things to know about this oil: For use in all 4-stroke marine engines. This oil is engineering approved for all marine 4-stroke applications including: outboard, MerCruiser, high performance, stern drive/inboard.

Is there a difference in marine oil and regular oil?

Marine engine oils

have to handle high RPM and constant loads experienced

by marine engines. … A marine engine oil has to resist shear, moisture and corrosion more than an automotive engine oil, and has to have extremely strong film strength to protect engine parts under constant stress and load.

What Year Did Mercury start making 4 stroke outboards?

When the phased-in environmental regulations on marine engines took effect in

1996

, Mercury was able to meet the new requirements with a complete four-stroke outboard line, complemented by its first-to-market, low-emissions, direct-injection two-stroke OptiMax technology.

What is a lower unit on an outboard?

The lower unit (or “foot”) of your outboard motor is

the bottom part that houses the prop and gear case

. … The main keys to lower unit maintenance are keeping fishing line and other debris from getting wound in the prop, and changing your lower unit oil regularly.

How often should you change outboard spark plugs?

Some boaters are adamant about changing their spark plugs every year or

100 hours

. PartsVu recommends religiously inspecting your spark plugs annually or every 100 hours, replacing them if they are fouled or damaged, and always replacing them every 300 hours.

What is the problem with using your boats engine to drive it onto a trailer?

NOTE – While many people drive the boat onto the trailer, it isn't advised. Using the engine to

assist trailering erodes the ramp bed, can lead to debris being sucked into the engine

, and can cause an accident! Make sure you drain all water from the boat – the bilge, the live well, the trailer lights, etc.

Do outboard motors need special oil?

Two-stroke outboards require

oil that meets the TC-W standard

, which indicates a marine oil designed for a two-stroke engine. Again, consult the owner's manual for specific two-stroke oil requirements.

Can I mix Quicksilver and Mercury oil?

Re: mercury oil

The mechanic at Bucks said to

not mix quicksilver

and merc premium because they coagulate and cause the engine to foul.

What is the difference between Mercury and Quicksilver oil?


THEY ARE EXACTLY THE SAME

. Mercury stuff is sold at Mercury dealers while Quicksilver is sold at Walmart, Academy etc. This question gets asked a lot in the Merc section. THEY ARE EXACTLY THE SAME.

What is the difference between Mercury and Quicksilver?

The main difference between the two brands is

where they are sold and the larger breadth of products available under the Quicksilver brand

. Mercury products are sold only by M ercury Marine dealerships. … Quicksilver offers 40,000+ parts across 12 product lines, and their products can be found throughout the world.

Is Marine oil necessary?

Although some boaters and anglers don't realize it, using a dedicated marine oil is

vital to protecting marine motors

. Protection against rust and corrosion is the number-one reason. Despite what most people assume, motor oils have no natural ability to protect against rust or corrosion.

Do Boats need special oil?

A boat engine requires

quality marine oil

if you want it to last and perform at its best. … Marine oil is designed specifically to do this. The second main difference between boat engines and automobile engines how hard they run. Marine engines run much faster and spend long periods of time at or near the red line.

Why should a boat's gas tank never be completely filled?

It's important to never fill the tank of your boat beyond 90% full. This leaves room for

gas to expand

and avoids the potential for overflow. Ensure that all air vents and valves to the gas tank are open.

Does boat motor oil go bad?

Once the container is opened, the shelf life of 2-stroke outboard oil reduces drastically. Generally, the

shelf life for an opened container of two-cycle oil is 2 years

. Anything more than that gives you bad oil, with the risk of ruining your engine.

How much oil should I put in my boat engine?

Most gas inboards or I/Os will take anywhere from

4.0 to 7.0 quarts

of oil and in some cases more. Check on the capacity of your engine from the owner's manual or tech pub. To begin the oil change process, start your engine and let it warm up for 5 minutes or more.

What weight is marine gear oil?

Lucas Oil 10652 Marine Gear Oil –

32 oz

.

What kind of oil goes in the foot of a boat motor?

You can use

any brand of lubricant that has a grade designation of API GL5 SAE 80 or 90 weight

. Make sure you do not mix different oil brands or weights. into the BOTTOM drain hole. Then slowly squeeze the bottle to force the oil into the lower unit.

What weight is outboard gear oil?


20W-40

Mineral Base (conventional)—for the larger outboards and warm climate this is best. However whatever oil you choose, ensure that it is of the right type and required viscosity and best suits your needs.

David Evans
Author
David Evans
David is a seasoned automotive enthusiast. He is a graduate of Mechanical Engineering and has a passion for all things related to cars and vehicles. With his extensive knowledge of cars and other vehicles, David is an authority in the industry.