Code P0010 stands for “A” Camshaft Position Actuator Circuit (Bank 1). The code indicates that
 
 your car’s primary computer
 
 , which is also referred to as the powertrain control module (PCM), perceives a problem with one of the engine’s VVT solenoids. … That means it turns the solenoid on and off really fast.
 What is camshaft position actuator circuit?
 
 Vehicles equipped with variable valve timing (VVT) use a special solenoid called a Camshaft Position Actuator. This solenoid is
 
 capable of regulating the oil pressure
 
 thus controlling the cam timing. … The P0010 code is set when the ECU detects a low voltage in the VVT circuit corresponding to the bank 1 intake cam.
 How do I fix error code P0010?
 
 Do a visual inspection of the bank 1 variable valve timing (VVT) control solenoid valve. Make sure to
 
 repair any frayed or faulty wiring or connectors
 
 . Once you have done this, clear the code and rescan to see if it is still present. Check to see if there is any engine sludge present.
 What causes a camshaft actuator to go bad?
 
 The variable valve timing camshaft actuators may stick due to
 
 dirty engine oil or a faulty control solenoid
 
 . A sticking actuator may cause a rough idle and the check engine light to illuminate.
 How much does it cost to fix a camshaft position actuator circuit?
 
| Repair Type Zip Cost |  Camshaft Position Actuator 96447 $181  | Camshaft Position Actuator 64713 $315 | Camshaft Position Actuator 36202 $2848 | Camshaft Position Actuator 52804 $500 | 
|---|
 Can I drive my car with a bad camshaft position sensor?
 
 
 Yes, it is safe to drive
 
 with a bad camshaft sensor. However, the performance of your engine will not be as good and fuel consumption may increase. In some cases, the camshaft may need replacement if there are any other symptoms of failure on this component. …
 What are the symptoms of a bad camshaft position sensor?
 
 
 A glowing check engine light, stalling, poor acceleration and bad fuel mileage
 
 are all possible signs your camshaft position sensor may be failing. Gone are the days of carburetors and distributors, replaced by a variety of sensors that help a car’s computer get the maximum performance out of the engine.
 Where is the camshaft actuator located?
 
 The intake camshaft actuator features a gray electrical plug and is located
 
 closer to the front of the vehicle on the top of the cylinder head
 
 .
 Where is the camshaft position sensor located?
 
 The camshaft position sensor can be found in
 
 the right side of the engine compartment at the rear of the valve cover
 
 .
 How long does it take to replace camshaft position sensor?
 
 Can You Replace a Camshaft Position Sensor Yourself? Yes. This is one of those jobs that almost anyone can do and is an easy way to save yourself the minimum labor fee (often close to $100) that a repair shop or dealership will charge you. It should take
 
 about 5-10 minutes
 
 to replace it.
 How do you check for a bad camshaft sensor?
 
 Touch one of your
 
 meter
 
 probes to either one of the sensor wires and the other to the other wire. Check your meter display and compare your reading to your manual specifications. In most cases, you’ll see a fluctuating signal between 0.3 volts and 1 volt. If there’s no signal, you have a bad sensor.
 What does a bad camshaft sound like?
 
 The symptoms of a bad camshaft include
 
 frequent backfiring and popping
 
 . You may also experience cylinder misfires at low and high speeds. Additionally, if your camshaft lobes are worn, you may hear tapping and ticking noises from the upper engine.
 How hard is it to replace a camshaft sensor?
 
It may be easiest to remove and replace the camshaft sensor from under your vehicle, but it can also be done from the top by removing the air filter housing.
 Is a camshaft expensive to fix?
 
 The cost for a camshaft replacement is
 
 between $1500 and $3000
 
 with labor costs and parts priced. You shouldn`t neglect engine servicing and oil changes then the camshaft won`t break.
 How many camshaft sensors does a car have?
 
 The
 
 two
 
 most common camshaft sensors you’ll see are the magnetic and Hall-effect types. Both transmit a voltage signal to an electronic control module or to the car’s computer.