All Honda vehicles, the Civic included, are recommended to have
80 foot-pounds of wheel lug
torque.
What torque should lug nuts be at?
| Hardware Bolt or Stud Size Typical Torque Range in Ft/Lbs Minimum Number of Turns of Hardware Engagement | 14 x 1.25 mm 85 – 90 9 | 7/16 in. 70 – 80 9 | 1/2 in. 75 – 85 8 | 9/16 in. 135 – 145 8 |
|---|
What is the torque spec on a Honda Civic?
| Model Trim Torque | CIVIC – ALL ALL / LX 80 ft-lbs | CLARITY ALL 80 ft-lbs | CROSSTOUR 17′′BASE / EX 80 ft-lbs | CR-V ALL / ALL 80 ft-lbs |
|---|
What should the torque be on?
Use torque sticks with
an air gun
or a torque wrench to get the correct torque. If your studs or lug nuts are sized between 12 X 1.25mm to 1.5mm or are 7/16-inch, torque the nuts to 70 to 80 foot-lbs; 14 X 1.25mm to 1.5mm, to 85 or 90; 1/2=inch 75 to 85; and 9/16-inch 135 to 145.
What is the torque setting for car wheels?
The optimum torque value for your car or mounted rims can be found in the vehicle manual. It depends on the car model, rim size, design (aluminium or steel rims) and number of bolts. It is normally
between 110 N⋅m and 120 N⋅m.
How do you rotate tires on a Honda Civic?
- Front-Wheel Drive: Swap the sides of your rear tires when you move them up to the front. …
- Rear-Wheel Drive: Swap the sides of your front tires when you move them to the rear. …
- All-Wheel Drive: Rotate your tires in an X-shaped pattern.
What is the torque spec for aluminum wheels?
Aluminum wheels should have the lug nuts torqued to
70 ft. lbs.
The beadlocks should be 20-22 ft.
What is the torque for lug nuts on Honda Civic?
Honda Civic Lug Torque
All Honda vehicles, the Civic included, are recommended to have
80 foot-pounds
of wheel lug torque.
How many ft lbs should lug nuts be?
Most automotive lug nuts are tightened to
90 – 120 ft. lbs
… Trucks will be more, about 120-150 ft. lbs.
What is the torque for oil drain plug?
20 to 25 foot-pounds
is the Torque specification for oil drain plugs.
How much torque does a car need?
Very heavy duty automotive fasteners require
between 200 and 1,000 ft. lbs of torque
, or even higher amounts. Applications include camshaft sprockets and harmonic balancers. Many off-road vehicles or performance racing vehicles will require torque applications in this range as well.
What should I torque my spark plugs to?
| Thread Size Recommended Torque Recommended Tightening Angle | New Plug | M14 20-30N・m About 1/2 turn | M14 20-30N・m About 2/3 turn | M18 30-40N・m About 1/4 turn |
|---|
Do I need to torque my wheels?
While
a torque wrench is not absolutely required
, it’s a good idea. You need to ensure the wheel is evenly clamped onto the hub. This prevents the wheel from warping and causing other issues. Using the lug wrench which comes with the car will get you down the road.
How tight should wheel bearings be?
The nut on the spindle should be tightened
until snug
, with no side-to-side play in the hub and then backed off, about a quarter of a turn. The nut finger should be tight until the castle nut or cotter pin is used.
What happens if you don’t tighten your lug nuts?
If the lug nuts or bolts are loose,
the wheel will not be held snugly against the hub of the vehicle
. When the vehicle is driven, the wheels will shake. The shaking will be felt in the steering, and likely throughout the whole car.
What happens if you over tighten wheel nuts?
If the wheel nuts are too tight, they can cause severe problems such as
stripping the fastener threads or stretching the wheel studs
. They could also warp the brake drums, brake discs or wheel hubs. With loose nuts, meanwhile, there’s a small risk that the wheel could come off while you’re on the road.
