How high should stove pipe damper be?
A damper is usually located approximately
12 to 18 inches
from the stove, prior to the spot where the pipe exits into a chimney, if present. The damper retains heat that escapes up the chimney or flue.
Do I need a stove pipe damper?
Newer models of wood stove don’t typically require a damper
. A damper was traditionally used on older, less efficient, models of stove to help reduce the flow of air leaving the firebox. Certified modern stoves meet stringent regulations and typically won’t need a damper to perform well.
How do you install a top damper?
How do you use a stove pipe damper?
- Orient yourself with the damper handle on the outside of your flue pipe or the exterior of your stove. …
- Open the damper all the way, if you are lighting a fire. …
- Close the damper about two-thirds of the way as the fire begins to catch and coals start to form.
Is a damper the same as a flue?
A damper is located in the flue of your chimney
. The flue is where the smoke escapes when the fire is going. Dampers are placed inside of the flue to help control ventilation. Your damper should have a chain or handle that you can access in order to open and close it.
Does closing the damper on a wood stove?
If you’re burning wood in your stove, you should make sure that the damper is open. If you close the stove’s damper when you have a fire burning you could be putting yourself at risk, not only of fire hazards but also of carbon monoxide poisoning.
When you have extinguished the fire, you can close the stove’s damper
.
Why do you need a damper on a wood stove?
A stove damper is an important part of any wood-burning stove.
It controls the amount of air that can flow into the firebox, allowing for regulation of both heat and draft
. The damper also prevents outside air from entering the chimney when it’s not wanted.
How do you connect stove pipe to wood stove?
- Measure the Pipe Flange. Measure the circular flange emerging from the stove. …
- Fit the Pieces Together. Check the stovepipe. …
- Seal With Stove Pipe Sealant. …
- Place the Pipe On the Stove. …
- Ensure Flange is In Place. …
- Add Additional Fittings if Necessary.
How do you seal a flue pipe on a stove?
For the first joint adjacent to the stove you should
fill the gap with thermal rope and then cover with black fire cement
, from a cartridge is the most convenient way to do this. Any other joints should be sealed with VITCAS Heat Resistant Silicone.
Does a wood burning fireplace insert have a damper?
Whether your fireplace is gas or wood-burning,
if it was built with a pre-fabricated insert, then it almost certainly has a damper
. And while older wood-burning fireplaces can function safely without a damper (gas fireplaces cannot), a chimney without a damper is just a gaping hole in the roof of your house.
How does a lock top damper work?
A Lock-Top Damper
seals tight, so virtually no air, and thus no heat or air conditioning gets lost up your chimney
. The Lock-Top also eliminates downdrafts, seals out rain which can deteriorate the inside of your chimney, and prevents entry by pests like squirrels, raccoon, and nesting birds.
What is a flue damper?
A flue damper is
a metal plate on a spindle fitted inside a flue system, usually in the first length of vitreous enamel connecting flue pipe
, which can be rotated by a small handle outside the pipe to reduce the adverse affects of a strong updraught (aka pull or draw).
How does a top damper work?
Unlike the traditional throat damper, a chimney top damper is installed at the top of the chimney. To operate the top damper,
a cable is installed down the flue to the firebox. Pulling and latching the cable closes the damper lid onto the rubber gasket
. A damper closed this way is practically air tight.
Should damper be open or closed?
The damper should be open when you have a fire going to allow the smoke and carbon monoxide to flow up the chimney and out of your living space
. If you start a fire with the damper closed, you will fill your home with smoke!
How do I know if my damper is open or closed?
Before lighting a fire, you can tell if the damper is open by placing your hand into the fireplace. If you feel a draft coming down the chimney, it is a good indicator that the damper is open. If you don’t feel any cold air coming down the chimney, it means that the damper is closed.
How do you fix a damper on a wood stove?
Is it OK to leave the flue open overnight?
The smoke from burning wood contains carbon monoxide, so in order to prevent this toxic byproduct from entering your home,
it is important to leave the flue open overnight
. This enables a draft to carry the compound out into the atmosphere, instead of sinking down the chimney and saturating the room.
