If the F2 error code has frozen on the oven after shutting down, then
unplug the oven for 30 seconds
. Plug the oven back in and see if the error code appears again. At times glitches will occur and the error code will randomly appear.
What does F2 mean on an oven?
The F2 error indicates
an open circuit in the oven temperature probe
. The answer Raquel F sent gives you good information on the oven temperature probe. Your range has a resettable thermostat in series with the oven temperature probe. If this thermostat opens the clock will display F2 and the oven won't heat.
How do I fix error code F2?
If the F2 error code has frozen on the oven after shutting down, then
unplug the oven for 30 seconds
. Plug the oven back in and see if the error code appears again. At times glitches will occur and the error code will randomly appear.
How do I reset the code on my GE oven?
If you still see an error code on the GE profile oven, control panel reset is the next step. You can perform a reset
by shutting off the breaker that supplies power to your oven
. Turn off the breaker in your home's electrical service panel and leave it off for a full 30 seconds. Then, turn the breaker back on.
How do you reset a GE oven?
Reset the electronic control. Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or
install the fuse to reset power
to the unit. This should reset the electronic controls on the range or wall oven.
What is a F2 error code?
If you have a GE oven, the error code F2 on the oven means that
the temperature sensor has detected a temperature in excess of the preset threshold
. … The cause could be a sensor malfunction.
Why does my washer say F2?
: The “F2” fault code indicates
it's taking too long to drain the tub of water in order to reset the pressure switch
. The problem is that the washer is not always able to drain water so that the water level switch can reset. This can happen if the wrong type of detergent is used or if you are using too much.
What does E6 F2 mean on a Whirlpool oven?
The E6-F2 error code indicates a problem with the touchpad or the electronic oven control. E6-F2 specifically means the
cancel key drive line is open
. You can't cancel this error code, but sometimes removing the power from the oven and reconnecting it will cure it.
Where is the temperature sensor in my oven?
Your temperature sensor is a probe that extends
into your oven on the top left corner of the back interior panel
. Reach into your oven along the ceiling, toward the left back corner. You should find it there.
What does F3 mean on a GE oven?
When the F3 code flashes on your GE oven, this indicates that there is
a fault with the oven temperature sensor
. There are a few parts that could be causing the fault. These include the wire harness, control board or the oven temperature sensor itself.
How do I troubleshoot my GE oven?
- Make sure your GE electric oven controls are set for either bake or broil if the oven does not heat, but the burners do heat. …
- Check the oven knobs and make sure they are in the right position if the device is not producing heat. …
- Unplug your GE electric oven and check the fuse.
How do you fix F3 error on GE oven?
Clear/Off. The oven control panel has a “Clear/Off” button, which is normally used to cancel an oven setting. When an error code, such as the F3 code, appears on the control panel screen, it might just be a temporary glitch. To determine if this is the case,
push and hold the “Clear/Off” button for two to five seconds
.
How do you fix F1 error on GE oven?
If you get the F1 and beep,
replace the ERC
. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad. If the code cannot be canceled, the electronic range control (ERC) has failed and it may need to be replaced.
Where is the temperature sensor on a GE oven?
The temperature sensor, also known as the oven temperature sensor assembly is usually found
in the back of the oven
. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary.
What does F4 mean on a GE oven?
F4 fault code usually means that
the oven sensor needs to be replaced
. Fault codes are programmed in all electronic ranges. These codes help GE Appliances Factory Service technicians quickly diagnose issues.
What does E2 and F2 mean on a dishwasher?
If this code appears on your dishwasher display, it means that there is
a communication failure between the electronic control and the touchpad
.