Truck Load of Gravel Cost. A truck load of gravel costs
$1,350 or more with a 10-yard minimum
, including delivery and spreading based on the rock type, amount, truck size (double or tri-axle), and travel distance. Most rock-fill jobs use a 3-man crew plus a tractor for $46 per hour that spread 12 cubic yards per hour.
How much gravel can a pickup truck hold?
However, here are some general guidelines to give you an idea of how many trips it might take for a big project: Full-size Pickup Trucks: Can usually handle 2 cubic yards of soil, 2-3 cubic yards of mulch, and
1 cubic yard of stone or gravel
.
How many pounds is a truckload of gravel?
Typically sand and gravel weigh approximately
1500 pounds
(3/4 of a ton) per scoop (1/2 cubic yard). One cubic yard (2 scoops) will weigh about 1.5 tons (3000 lbs.). Soils typically weigh a little less, approximately 1000-1200 pounds per scoop.
How much will a ton of gravel cover?
A ton of gravel will cover
approximately 100 square feet, 2 inches deep
.
What is the cheapest gravel for a driveway?
Crush and run
is one of the cheapest materials that can be used in a gravel driveway at about $0.40 per square foot. Cost per cubic yard is about $20 and per ton about $28.
How much gravel is in a scoop?
1 scoop=
3/4 yard
and weighs approximately 3/4 ton/1500 lbs.
How much does a 50 lb bag of gravel cover?
A 50-pound bag of pea gravel is equivalent to
0.5 cubic foot
, so two 50-pound bags cover 1 cubic foot. Knowing that a 50-pound bag of pea gravel averages 0.5 cubic foot makes the calculation easy — and one most smartphone calculators can complete.
How many ton of gravel do I need?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the
total and divide by 21.6
(the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.
How many square feet will 5 tons of gravel cover?
Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel,
100 square feet per
ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.
How do I calculate how much gravel I need?
Measure the length and width of your driveway in feet. Multiply the
length by the width to
get surface area and divide the result by three because 4 inches is 1/3 of a foot. You now have the volume of gravel needed in cubic feet. Divide the volume in cubic feet by 27 because there are 27 cubic feet in a cubic yard.
What area does a ton of gravel cover?
Cloburn – The Home of Lanark Red Granite
Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover
14 square metres
. For pedestrian pathways, 35mm is normally sufficient in which case 1 tonne will be sufficient to cover approximately 20 square metres.
What size gravel do I need for my driveway?
In general, driveway gravel should be relatively large,
between about 3/8 and 3/4 inch in diameter
, as compared to the gravel used for footpaths, which is typically 1/4 to 3/8 inch in diameter. Another factor to consider is the amount of very small granular material, called “fines,” in the gravel.
How much is a dump truck full of gravel cost?
A truck load of gravel costs
$1,350 or more with
a 10-yard minimum, including delivery and spreading based on the rock type, amount, truck size (double or tri-axle), and travel distance. Most rock-fill jobs use a 3-man crew plus a tractor for $46 per hour that spread 12 cubic yards per hour.
What is #2 gravel?
This
primarily 1′′ crushed, washed gravel with a top size of
1-1/2′′ is often used for drainage around perforated pipe, under concrete slabs, and as a coarse driveway topping for soft, very muddy driveways.
Is asphalt cheaper than gravel?
Economical option. Homeowners appreciate the sleek appearance of an asphalt-paved driveway at a lower cost than concrete or paver surfaces. Asphalt driveways typically cost $2 – $5 per sq foot to install –
more than gravel
, but much less than many other options. …
How do you calculate pea gravel?
Measure the length, width and depth in feet of the area to be covered.
Multiply the three numbers together. Divide by 27
to get the number of cubic yards of pea gravel needed. For example, if the area is 9 feet square and the gravel is to be a foot deep, multiply 9 by 9 by 1 to get 81.
