Where is the temperature sensor on a 1999 Jeep Grand Cherokee? there is a temp sender that feeds the gauge/dummy light…..it is located
at back of engine on driver's side beside the valve cover, screwed into the intake manifold
, in between the fuel rail and injector harness rail…see pic below…
Where are coolant temp sensors located?
The Engine Coolant Temperature Sensor can be located in a few places, depending on the vehicle and its manufacturer. It is most often located
close to the thermostat of the cooling system
or inside of it. The cooling system is located beneath the air intake pipe and behind the right cylinder.
Where is the outside temperature sensor on a Jeep Grand Cherokee?
The ambient temperature sensor is a variable resistor mounted to a bracket that is secured with a screw to the
right side of the headlamp mounting module grille opening
, behind the radiator grille and in front of the engine compartment.
What happens when a temperature sensor goes bad?
If the coolant temperature sensor goes bad it can
send a false signal to the computer and throw off the fuel and timing calculations
. … This will cause the computer to think the engine is cold, even when it is not, and as a result will use more fuel than necessary.
What are the signs of a bad temperature sensor?
- Poor Fuel Economy. …
- Irregular Temperature Readings. …
- Black Smoke from Your Exhaust. …
- Your Engine is Overheating. …
- Your Check Engine Light is On.
Can you drive with a bad temperature sensor?
It is possible to drive a vehicle with a faulty coolant temperature sensor
as the management system defaults to a static reading. A vehicle's coolant sensor is a critical component used by the engine management system. It directly affects, cooling and fueling of the engine and therefore affects how the engine performs.
Does the coolant temp sensor control the fan?
The sensor works by
measuring the temperature
that's being given off by the thermostat and/or the coolant itself. The temperature is then sent to the on-board control system. … As the control system receives the temperature from the CTS, it may trigger the cooling fan to either shut off or turn on.
How do you clean a temperature sensor?
- Wash The Thermometer In Warm Water. Washing your thermometer probe wish warm water will remove any residue that may be on the probe, and it'll help start the sanitizing process. …
- Sanitize The Thermometer With Alcohol. …
- Rinse The Thermometer. …
- Air Dry The Thermometer.
How do you check a temperature sensor?
- How to test a faulty thermocouple or resistance thermometer?
- Check if the -ve and +ve leads swapped.
- Check for any thermocouple cable wiring issues.
- Check for local heat source issues.
- Check Temperature Transmitter Settings.
- Check temperature controller settings.
- Troubleshooting temperature sensors with a multimeter.
How much does it cost to replace a coolant temperature sensor?
The average price for an engine temperature sensor replacement is
between $150 and $193
. Labor costs are between $82 and $105 while parts are between $66 and $88.
What does a temp sensor do?
A coolant temperature sensor (CTS) (also known as an ECT sensor or ECTS (engine coolant temperature sensor) is
used to measure the temperature of the coolant/antifreeze mix in the cooling system
, giving an indication of how much heat the engine is giving off.
Why is my car reading the wrong temperature?
Your car actually has a thermistor – not a thermometer. Car thermistors are a poor representation of the actual outside temperature. This is because
the thermistor is exposed to re-radiated heat from the road surface
.
Can a bad coolant temp sensor cause hard start?
If the sensor is reading too high of temperature when compared to the ambient air temperature sensor when first started then the computer would see it as a problem and turn on the check engine light to use a known good reading.
No start will not be caused by the sensor
.
How long does it take to replace a coolant temperature sensor?
The actual process of replacing the coolant temperature sensor is extremely simple. However, the difficult work comes in the preparation of the cooling system – both before and after. Tip: This job should only be completed when the engine is cold and has not been running for
a minimum of one hour
.
How do I know if my thermostat is stuck open?
A thermostat stuck in the open position constantly
pushes coolant into the engine and causes a lower operating temperature
. Your temperature gauge will show a needle that barely increases or remains at the lowest setting.
How do you fix coolant temperature?
- Let the car's coolant cool for 15 to 20 minutes.
- Locate the thermostat.
- For better clearance, jack up the front end of the vehicle.
- Remove the radiator cap.
- Drain the radiator, according to instruction sin your car's repair manual.
- Remove the thermostat.