Among the given instructions,
CALL instruction
will require maximum T-states for execution.
How many T states are required for the longest instruction in 8085?
Summary − So this instruction SPHL requires 1-Byte, 1-Machine Cycle (Opcode Fetch) and
6 T-States
for execution as shown in the timing diagram.
How many T states are there?
State | Location United States | Number 50 | Populations Smallest: Wyoming, 576,851 Largest: California, 39,538,223 | Areas Smallest: Rhode Island, 1,545 square miles (4,000 km 2 ) Largest: Alaska, 665,384 square miles (1,723,340 km 2 ) |
---|
How many T States are used in out instruction?
Summary − So this instruction OUT requires 2-Bytes, 3-Machine Cycles (Opcode Fetch, Memory Read, I/O write) and
10 T-States
for execution as shown in the timing diagram.
How many T states are required for execution of in 30H instruction?
IN instruction means Input data to Accumulator from a port with 8-bit address.IN 30H is a 2 byte instruction which requires
3 machine cycles
i.e. Opcode fetch, read, read(operand read from the 8 bit port address).
What is relationship between instruction cycle and T State?
The time required by the microprocessor to complete an operation of accessing memory or input/output devices is called machine cycle.
One time period of frequency of microprocessor is
called t-state. A t-state is measured from the falling edge of one clock pulse to the falling edge of the next clock pulse.
What type of instruction is pop?
Mnemonics, Operand Opcode(in HEX) Bytes | POP PSW F1 1 |
---|
How are T states calculated?
The calculation of T-states don’t have any specific step. It depends upon the program & it’s logic. In short I will say :
Find total number of T-states& multiply it with clock period & get the execution time
.
Which register pair is used to indicate memory?
H and L register pair
is used to act as memory pointer and it holds 16 bit address of memory location.
What is the need for interfacing?
Interfacing is one of the important concepts in microcontroller 8051 because the microcontroller is a CPU that can perform some operation on a data and gives the output. However to perform the operation we need
an input device to enter the data
and in turn output device displays the results of the operation.
Why opcode fetch has 4 T States?
Opcode Fetch in 8085 is typically 4 T states. However for CALL instruction, it takes 2 additional T states. It is because –
After the fetch and decode, the stack pointer has to be decremented ahead of the first Memory Write cycle that will store the current PC’s MSB to the stack
.
Which one is 3 byte instruction?
Three-byte instruction is the type of instruction in which the first 8 bits indicates the opcode and the next two bytes specify the 16-bit address. The low-order address is represented in second byte and the
high-order address
is represented in the third byte.
Which flag is affected by CMA instruction?
CMA does not affect flags
. If you need to evaluate a logical condition on the result of CMA, you should use CPI 0 after CMA.
Which instruction is not possible in 8085?
Explanation: In
Memory Direct Addressing Mode the data transfer between memory-to-memory
is not possible. In the microprocessor, most of the instruction sets allow one register operand or one memory operand, and format of this structure makes designing the instruction decoder easier.
Which group of instructions do not affect flag?
As there is no arithmetic or logical operation being performed, no flags are affected by
data transfer instructions
. Arithmetic instruction: Arithmetic Instructions are the instructions that perform basic arithmetic operations such as addition, subtraction, and a few more.
What are the basic steps for the execution of an instruction?
- Five-stage pipeline.
- (non-accumulator.
- based-processor)
- Fetch the instruction.
- Decode the instruction and get the source operand.
- Get the destination operand.
- Perform the operation.
- Store the result.