Where Is The Headlight Relay Located?

Usually, it is

under the hood of the car

. The point where your fuse panel is most likely located. On the other hand, it may also be located inside the cab of the car, this would be the case if your car comes with an interior fuse box.

What are the symptoms of a bad headlight relay?

• Headlight doors don’t open. One of the first symptoms of a failed headlight closure relay is headlight doors that don’t open. …
• Headlight doors stuck open. …
• Headlight doors operate erratically and open or close on their own.

How do you check a headlight relay?

Set your meter to read in

“Volts DC

,” and touch the probes to the corresponding ground and power terminals in the box. You should see about 12 volts with the headlights turned on, and nothing with them off. If you see this voltage, but the headlights still aren’t working, replace the relay.

What relay controls headlights?

All relays, including your

headlight closure relay

, are used to keep high amperage and voltage systems away from the driver as a safety measure. Used in “flip-up” lights, which fold out of the body of the vehicle, headlight closure relays are essential for headlight operation.

How do you change a headlight relay?

1. Materials Needed.
2. Step 1: Locate the headlight closure relay. …
3. Step 2: Remove the fuse box cover or lid. …
4. Step 3: Remove the old relay. …
5. Step 4: Insert the new relay. …
6. Step 5: Test the headlights. …
7. Step 6: Reattach the fuse box cover.

What is a bad headlight relay?

The most common sign of a bad headlight relay is

headlights that don’t work

. A headlight relay will typically fail in the open position, preventing voltage from reaching the headlights. If the low beam relay fails, the low beams won’t work.

Does each headlight have its own relay?

Headlight Fuse or Relay

All the electrical systems in your car, including the headlights, are

protected with fuses

. … If a headlight fuse blows, it could cause the headlights to stop working. Most headlight systems are also designed with a relay that switches the power between low beam and high beam headlights.

Why do my headlights not work but my brights do?

2. Headlight Fuse or Relay is Bad. Like all electrical systems, the headlights in your vehicle have a

fuse in the circuit to prevent too much electricity from reaching the bulb

. There will also be a headlight relay that switches power from the low beams to the high beams.

Does one fuse control both headlights?

The first, and easiest, component to check is the headlight fuse. Depending on how your headlight circuit is set up,

there may be one fuse or multiple fuses for the headlights

. If you find a blown fuse, then replacing it may fix the problem. … You should find battery voltage on both sides of the fuse.

How much does it cost to replace a headlight relay switch?

Headlight Dimmer Switch Replacement Cost – RepairPal Estimate. Labor costs are

estimated between $67 and $85

while parts are priced at $88. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

What does HDM relay stand for?

If you know how to replace the HDM which stands for

Headlamp Driver Module

, is # 46 in the fuse box compartment on left side of engine.

What does H LP mean?

H-LP stands for

headlamp

, guessing the CLN might mean cleaner, as in a headlamp squirter or a wiper system neither of which are US Spec.

Why relay is used in headlights?

By using a relay we

move the high current switching away from the headlight switch so that the switch only sees a small current

– in the range of a few thousands of an amp. This solves part of the problem. You will need two relays – one for low beam and one for high beam.

How do you fix both headlights not working?

Solution: If both headlights aren’t working, it’s unlikely that a bulb is at fault. The likely cause is a fuse, headlight relay, headlight switch, dimmer switch or a wiring fault. About the only cause that is an easy fix is a

blown fuse

.

When I turn my high beams on the lights go out?

Most of the

time both bulbs are bad

. The connections to the bulbs could be faulty as well. If you’re unable to pinpoint the issue, have a certified technician, like one from YourMechanic, diagnose your lights firsthand for an accurate repair.