3) In the class of all amplifiers with dc gain K, > 1 + fi, monotone frequency response, using only resistors and at most two operational amplifiers, and with output taken from the output of an operational amplifier,
Circuit 5
has the largest bandwidth.
What is bandwidth in amplifier?
The Bandwidth (BW) of an amplifier is defined as
the difference between the frequency limits of the amplifier
. … The range of frequencies within a band is known as bandwidth. An amplifier also known as an amp is an electronic device that enhances the power of a signal.
How can I increase the bandwidth of my amplifier?
The best way to increase the bandwidth of an opamp is
by decreasing the closed loop voltage gain of opamp
. Explanation: Opamp has a very low bandwidth(around 5Hz) and to increase the bandwidth, we apply negative feedback which decreases closed loop gain.
What is bandwidth in common emitter amplifier?
Most amplifiers have
relatively constant gain over a certain range (band) of frequencies
, this is called the bandwidth (BW) of the amplifier. Fig. 1 Typical frequency response of an amplifier. As the frequency response curve shows, the gain of an amplifier remains relatively constant across a. band of frequencies.
What is the bandwidth of a transistor?
fT: Gain bandwidth indicates
the maximum operating frequency of the transistor
. At this time the collector current ratio with the base current is limited to 1 (hFE=1). As the frequency of the signal input applied to the base approaches the operating frequency, the hFE begins to reduce.
Why 3dB is cut-off?
It’s not really arbitrary. It’s because decibels are logarithmic, and the log (base 10) of 3 is about 50% power. So the 3 decibel cutoff is
where power drops off by a half
. 3 dB implies 1/2 the power and since the power is proportional to the square of voltage, the voltage will be 0,707 of the pass band voltage.
What is the formula of bandwidth?
Bandwidth is measured between the 0.707 current amplitude points. The 0.707 current points correspond to the half power points since
P
= I
2
R, (0.707)
2
= (0.5). Bandwidth, Δf is measured between the 70.7% amplitude points of series resonant circuit.
How can reduce the overall bandwidth of amplifier?
There are several ways to ensure that the high frequency cut-off occurs at an appropriate frequency, reducing noise and instability but keeping the important harmonics in an audio amplifier. One such way is in a multi stage amplifier is to
use a low pass filter in one of the amplifier stages
.
How do you calculate gain bandwidth?
Open-loop Frequency Response Curve
For example, from the graph above the gain of the amplifier at 100kHz is given as 20dB or 10, then the gain bandwidth product is calculated as:
GBP = A x BW = 10 x 100,000Hz = 1,000,000
.
Why is gain bandwidth product constant for an amplifier?
The gain-bandwidth product (GBW) is calculated
by multiplying the absolute value of the gain with ω
. which shows that the gain-bandwidth product is a constant, because it is a product between two constants: the op amp open-loop gain and the corner frequency.
How do I check bandwidth of multistage amplifier?
It is the frequency for which the overall gain falls to 1/√2 (3dB) of its midband value. In multistage amplifier f
L
(n) is always greater than f
L
and f
H
(n) is always less than f
H .
So the bandwidth of multistage amplifier is
always less than single
stage amplifier.
What is 3dB bandwidth?
The half-power point or half-power bandwidth is the point at which the output power has dropped to half of its peak value; that is, at a level of
approximately -3 dB
. In filters, optical filters, electronic amplifiers, the half-power point is a commonly used definition for the cutoff frequency.
How is 3dB bandwidth calculated?
BW (Hz) = f
0
× (BW / 60) × √2
For example, at a bandwidth setting of 60/60 a filter centred on 1 kHz with a gain of −6 dB will have a bandwidth of 1,414 Hz between the points where its response crosses −3 dB.
Can current flow backwards through a transistor?
Yes current can flow in both directions
. An NPN transistor backwards is also an NPN. There will still be a reverse beta, however, the backwards NPN transistor won’t work as well as a correctly oriented one will.
What is the relationship between gain and bandwidth?
Gain and bandwidth in an amplifier are
inversely proportional to each other
and their relationship is summarized as the unity-gain bandwidth. Unity-gain bandwidth defines the frequency at which the gain of an amplifier is equal to 1.
What is 10th bandwidth?
Bandwidth is
a range of frequencies within a continuous set of frequencies
. It is measured in Hertz. … For transmitting sounds or speech, the frequency range of 300 Hz to 3100 Hz is sufficient and hence the current telephones operate at a bandwidth of 2800 Hz.
