In order to do a soft reset for the radio on a 2008 Jeep Grand Cherokee You're first going to need to give the vehicle power and then turn on the radio.
Now press down the volume and the tuning knobs for 10 seconds
. After the 10 seconds are up the radio should flash and then come back online.
How do I reset my Jeep Grand Cherokee radio?
Push and hold the volume and two knobs at the same time for about 10 to 20 seconds until the radio power is off. Once the system shut off it will quickly turn back on and take about
a minute
or so to fully come back online.
How do I unlock my Jeep Grand Cherokee radio?
Once you have the serial number and model or part number you can get the original Jeep Grand Cherokee Radio Code to unlock the radio using our secure online service or you can request the radio
code by telephone – 020 8243 8962
.
How do you reset the computer on a 2008 Jeep Grand Cherokee?
- Disconnect the battery by removing the positive battery cable. …
- Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
- Reconnect the positive cable to the battery.
- Turn the key to on but do not start.
- Turn the headlights on.
Where is the radio fuse on a Jeep Grand Cherokee?
The fuse for the radio in a 2018 Jeep Grand Cherokee can be found in the fuse panel that is located
in the driver's footwell under the dash
.
How do I find the security code on my jeep radio?
The best place to locate a radio code is
in the owner's manual of your car
. In most cases, the owner's manual will be located in your glove box and will include general automotive service and maintenance tips, along with instructions on how to operate each system on the vehicle.
How do you reset the computer on a 2008 Jeep Patriot?
- Insert ignition key and turn to “ON” (not start).
- Wait for all idiot lights to go out. …
- Slowly depress the accelerator pedal all the way to the floor.
- Slowly release the accelerator pedal until it's all the way back up.
- Turn the ignition key to “OFF”.
- Start the engine.
How do you reset the computer on a 2018 Jeep Grand Cherokee?
How do you reset the computer on a 2018 Jeep Grand Cherokee? To do a soft reboot of Your touch screen in Your 2018 Jeep Grand Cherokee You'll need
to hold down the enter and volume buttons for 15 to 25 seconds
. After this time has passed the screen will flash and then it should come back on and work like normal.
How do you reset the computer on a 2008 Jeep Wrangler?
- Open the Wrangler's hood and prop it up with the support bar.
- Loosen the bolt on the negative battery clamp using a ratchet and socket. …
- Wait 30 minutes for the computer to reset itself.
- Put the negative battery clamp back onto the negative battery terminal and tighten the bolt.
How can you tell if an IOD fuse is blown?
- Parasitic battery drain.
- No fuse error message.
- Dash cluster blinking wildly.
- Engine won't crank.
- Radio, dome lights, and cargo lights quite working.
- Windows wouldn't go down.
- Horn sounding when the doors are locked.
How do you tell if a fuse is blown in a car?
Remove the fuse from its holder. In some cases you may need a small screwdriver to unscrew the fuse holder cap. Look at the fuse wire. If there is a visible gap in the wire or
a dark or metallic smear inside the glass
then the fuse is blown and needs to be replaced.
Where is the fuse for the radio on a 2007 Jeep Grand Cherokee?
The fuse panel is on
the lower instrument panel just to the left of the steering column
.
How do I reset my car radio without the code?
Turn on your radio and see if it displays CODE or LOC. If it does, turn off the radio.
Press and hold down the audio power button together with the SEEK button for about 50-60 minutes
. Then, it will turn on without entering the radio code.
How do you reset the anti-theft code on a Jeep?
Press the power door-lock switch on the keyless entry fob
. Close the driver's side door. Leave all doors closed for about 16 seconds until the Vehicle Security Light on the instrument cluster stops flashing quickly. When the light flashes at a slower rate, this signifies that the system has been reset and rearmed.
Where is the anti-theft code on a Jeep Cherokee?
You can find this serial number on the anti-theft identification card usually
placed in the glove box
at the time of purchase. You can also find the serial number of the radio on the screen of your Jeep radio itself.
