Press Read or Enter on the scanner, depending on the scanner model that you have. Please scroll down
to the I/M Readiness menu and select it
. Look at all the systems. If most of them say NOT READY, it means the check engine light was recently reset.
How far do you have to drive to reset the check engine light?
To make sure the check engine light does not reappear, it's recommended that you drive your car
30 to 100 miles
. This enables the vehicle's “Drive Cycle” to reset, as the various sensors need time to recalibrate.
Will a check engine light clear itself?
Your vehicle's
check engine light will will reset by itself once the issue or problem has been repaired
; this is true for most models. … If you are certain that you have resolved the issue that caused your check engine light to come on in the first place, then the light should reset itself after at least 20 cycles.
How do you tell if OBD codes have been cleared?
If the vehicle does not support the above datapoints you can use
the smog check feature
to check for indications of codes being recently cleared. When codes are cleared all vehicle emissions tests are reset and will display a status of ‘not complete'.
Will check engine light come back on after reset?
It's possible that
the warning light won't come back on after you clear the code
. Then again, if the light does come on again soon, you must conclude that you do have an issue that needs to be addressed. And if you can't handle the repair yourself, then you should take it to a shop and have it attended to.
Can AutoZone take off check engine light?
Did you know that you can get your check engine light
scanned for free
? Any of the major parts stores in the country, such as: Napa, Advance Auto, Autozone and O'Reilly's, will scan your vehicle, and tell you the P codes for no charge at all.
Can AutoZone reset your check engine light?
Yes
, we can help you clear your code; it's called telling you how to fix your damn car. Like others have said, even after clearing it, the light will come back on within 30-50 miles of driving.
What is the most common reason for check engine light?
Replacing a faulty oxygen sensor
— a sensor used to optimize a vehicle's fuel-to-air mixture to increase gas mileage and reduce emissions — is the most common cause for a check engine light.
How can I get my check engine light off to pass inspection?
By the way the easiest way to turn off the check engine light would be to
disconnect
the battery for 30 seconds. Inorder to pass inspection your car needs to complete a full drive cycle so that all (8) internal monitors have a status of “Ready”.
Can low oil cause the check engine light to come on?
Low oil pressure
: If your car is low on oil, it can cause your check engine light to go off. This is often shown in its own glowing light along with the check engine light on the dashboard. Overheating: If your car's engine temperature is heating up, it can once again trigger the check engine light.
Can I clear codes with a code reader?
The
OBD2 scanner
can be used to troubleshoot automotive service codes, as well as to clear the codes. … There are many states where a vehicle can't be registered if there is a check engine light on the dashboard, and the OBD2 scanner can clear these codes reasonably quickly.
How long does it take for engine codes to clear?
On clearing the codes with the “Erase Codes” function, the system status changes to “Not Ready”. Drive for
50 to 100 miles (80 to 160 km)
. Take several individual trips until the system reads the status of all the components once more. “Several trips” means you shut off the engine and start another trip each time.
How long does it take for a car computer to reset?
The readiness monitors will remain until the car has been driven long enough for the computer to evaluate the various system and sensors. The amount of time can vary based on the vehicle. In some cases it can take
up to 100 miles
for all of the computer monitors to completely reset.
Why did my check engine light turn on and then off?
In a perfect world, you'll find that a check engine light on and off intermittently is being
caused by a loose gas cap
. … But many times, a check engine light will be caused by something other than a loose gas cap. It can, for example, be caused by a faulty oxygen sensor.
How long does it take for an o2 sensor to reset?
Turn the ignition to the on position but do not turn on the engine (it will not start anyway).
After five minutes
, reinsert the fuse. The lamp of the check engine will blink and then turn off, indicating that your ECU has been restored.
