Will A C6 Transmission Bolt Up To A 460? - Fixanswer

It has a stall speed of 1,800 rpm and a two-wheel-drive slip yoke for its tail housing, but it doesn’t have a hard input shaft. The horsepower of the C6 stock transmission has been measured at

300 horsepower

, while the torque has been rated at 250 nM.

Will a C6 transmission bolt up to a 351 Cleveland?

Sorry the 351 C uses a small block bolt pattern on the trans the 351 M uses a big block bolt pattern and will swap with

no problem

. You can use your internal components from your current C6 in a big block C6.

What engines fit a C6 transmission?

The C6 was used in trucks and cars with larger engines. Five different bell housing varieties exist for use with various Ford engine families: The Windsor pattern was used on the 300 I6, the Ford Windsor engines and the 351 Cleveland. The 460 pattern was used on the 351M and 400 and all of the

Ford “385”

engines.

Will a 429 bolt up to a C6 transmission?

The 351m, 400, 429, 460 all bolt up to the

C6

transmission without any adapters.

Which transmission is better C4 or C6?

The C4 transmission was primarily used in cars. The

C6 transmission could handle more power

. Due to the ability to handle more power, the C6 transmission was used in many Ford trucks with bigger engines, and in larger cars that were manufactured with bigger engines.

What replaced the C6 transmission?

Ford C4

and C6 Automatic Transmission History and Facts. Literally millions of Ford cars and trucks were equipped with C4 and C6 automatic transmissions between the introduction of the C4 in 1964 and the replacement of the C6 in the 1980s.

Will a C6 transmission fit a 351W?

Registered. — No, that

351W will not bolt onto

your 351M C6. — No, all 351W engines used the 351W bellhousing pattern, shared by the 302, 289, 351C, and 300-I6. — Your C6 uses a pattern shared by the 351M/400M (same engine block), and 429/460.

Can you add overdrive to a C6 transmission?

Adding overdrive to a C6 is physically impossible

, but the 4R100 can donate its forward planetary gear set for shorter first and second gear ratios. This creates a “wide-ratio” C6.

How do I know if my transmission is a C6?

Ascertain where the drain plug is situated at the transmission pan.

If the plug is at the side of the transmission’s pan, it is the C6

but on the bottom means it’s a C4. Determine where the speedometer driver gear is located.

How does a C6 transmission shift?

The transmission

will shift through the gears

, but will not downshift back to low gear when coming to a stop. … There is a delayed transmission engagement or it will not engage forward or in reverse. • The transmission slips in forward and reverse and a whining noise comes from the front pump or torque converter area.

Will a C6 transmission fit a 390?

No, C6 transmissions are engine family specific as the bellhousing & trans are a one piece casting ie, small block

C6 will only fit Cleveland or Windsor

, FE (390 etc) will only fit FE, & 385 series (429, 460 etc) will only fit these engines (but will also suit 351M & 400M).

Is a Ford C6 transmission good?

How good is a Ford C6 transmission?

The C6 is the strongest, most durable light duty automatic Ford has made

. It was designed in the 60’s during the horsepower wars. The E4OD / 4R100 is not necessarily a “crap” transmission, it is based on the C6.

Is the Ford C6 transmission a 4 speed?

The C6 is a

non-electronic, three-speed transmission

. The AOD features a four-speed, non-electronic transmission. It was not until 1992 that Ford introduced the electronic version of the AOD, the AODE.

Will a C4 transmission fit a 351?

yes

. the 351C uses the same bellhousings as the small blocks. However, one thing to remember is if you build up the engine much or plan on racing the stock C4 is a weaker transmission than a C6.

How long is a Ford C6 transmission?

The C6 has a

case length of 20′′

, which includes the bellhousing. This transmission was used up to all three Ford block bolt patterns.