The most common type of wall used for a manufactured home is called
Vinyl-Over-Gypsum or VOG for short
. VOG is drywall that is coated in vinyl wrap.
What are older mobile home walls made of?
Older manufactured homes usually have a faux wood paneling or walls made from
either paper on gypsum, or POG wallboards
, or vinyl on gypsum referred0 to as VOG panels or VOG wallboards. Vinyl on gypsum (VOG) panels has a laminated-like coating that holds the gypsum together.
What are mobile home wall panels made of?
Manufactured homes usually use
vinyl-on-gypsum (VOG) wall panels
rather than standard drywall. Instead of using tape to cover the seams, as is done with drywall, the joints are covered with batten strips during assembly.
Do mobile homes have drywall?
Most mobile homes are constructed to give an eight-foot ceiling height, so the
drywall sheets
should fit between the floor and ceiling. … Mobile homes are designed to be light, but the walls still have wooden studs and manufacturers will often use 1/4-inch paneling to cover the framing.
How thick are the walls of a mobile home?
Many mobile homes have wall material that is
1/4′′ to 3/8′′ thick
. there generally is not enough strength in this material to support the weight with drywall anchors alone.
Is drywall too heavy for mobile home?
Drywall that is
5/8′′ thick
is, of course, a little heavier, at 2.31 pounds per square foot or 73.92 pounds per sheet which is entirely too much for mobile home ceilings. … 1/2′′ thick drywall is the most recommended for mobile home ceiling replacements. assuming the trusses can handle it.
Can you replace walls in a mobile home?
Single-wide mobile homes are designed to be light, but the walls of most of them still contain wooden studs. Manufacturers often cover the walls with 1/4-inch paneling, but the studs can support drywall, so
there's nothing preventing you from
removing the paneling and replacing it.
What size sheet rock is used in mobile homes?
Most original sheetrock in mobiles are
3/8 thick
, If you use mollys for 1/2′′ you should be fine. Mobile homes are designed to be light, but the walls still have wooden studs and manufacturers will often use 1/4-inch paneling to cover the framing.
Are mobile home interior walls load bearing?
Do Mobile Homes Have Load Bearing Walls?
Single wide mobile homes do not have load-bearing interior walls
, but double wides do. … For example, some companies screw the wall studs to the roof studs. A double-wide mobile home is basically two single wides connected to one another by what is called the ‘marriage line.
Can you hang a TV in a mobile home?
Mounting a TV in a mobile home requires
knowledge
of the home's wall material, and the width and type of studs within the walls. Most wall materials alone will not support a TV's weight. Drilling in the center of studs and using the mount manufacturer's recommended hardware should offer the best hold.
Is paneling cheaper than drywall?
But is paneling cheaper to use than drywall? Because prefinished wall paneling varies so much in price, it is hard to determine the actual cost difference. But in general,
paneling is more expensive
. While paneling varies from $30 to $90 per panel, drywall sheets are about $10 to $30 per sheet.
How much weight can a mobile home ceiling hold?
In general, a mobile home roof can support a live load of
20 pounds per square foot
. A live load is a temporary addition to the weight already supported by the roof. A well-built roof may be able to support up to 30 pounds per square foot.
Do mobile homes have formaldehyde?
Formaldehyde is a colorless, strong-smelling gas. It is used to make building materials and household products. Formaldehyde is
used to make walls
, cabinets, and furniture in trailers and mobile homes.
What kind of ceiling is in a mobile home?
Most mobile homes and older manufactured homes (or lower end, more affordable models) have ceilings made
of gypsum
instead of drywall. Gypsum is a natural mineral used for blackboard chalk, drywall, and wallboards in mobile homes.
How do you remove a wall in a mobile home?
- Step 1: Turn Off Electricity and Water. …
- Step 2: Test for Wiring and Plumbing. …
- Step 3: Remove Trim and Battens. …
- Step 3: Flooring. …
- Step 4: Removing the Wall (a bit at a time) …
- Step 5: Loosen the Bottom Plate from the Subfloor. …
- Step 6: Remove the Top and Bottom Plates.
What are VOG panels?
VOG, as the name implies, is
a wall-paper-like coating over sheetrock (gypsum) panels
. A similar matching covering is on the batten strips used between the VOG wall-board sections, to give it a more finished look.
