The cost of gravel ranges from $10 to $50 per ton, $15 to $75 per yard, $1 to $3 per square foot, or
$1,350 per truck load
depending on the rock type, volume, and travel distance.
How many square feet does a ton of pea gravel cover?
Consult with the local supplier to find the density of the pea gravel product. In general, a ton, or 2,000 lbs., will cover
100 square feet at a 2-inch depth
.
How much is pea gravel per ton?
| Formula multiply the mass value by 2000 |
How many yards are in a ton of pea gravel?
Multiply your cubic yards by
1.3
to find the total number of tons you’ll need. (A single cubic yard of pea gravel weighs about 1.3 short tons.)
How do I calculate how much pea gravel I need?
Measure the length, width and depth in feet of the area to be covered.
Multiply the three numbers together. Divide by 27 to
get the number of cubic yards of pea gravel needed. For example, if the area is 9 feet square and the gravel is to be a foot deep, multiply 9 by 9 by 1 to get 81.
How much will a 50 lb bag of pea gravel cover?
A 50-pound bag of pea gravel is equivalent to
0.5 cubic foot
, so two 50-pound bags cover 1 cubic foot. Knowing that a 50-pound bag of pea gravel averages 0.5 cubic foot makes the calculation easy — and one most smartphone calculators can complete.
How thick should pea gravel be?
Add pea gravel to a depth of
about 2-1/2 inches
. Use a garden rake to smooth high spots and fill low spots as you go. Remember, the border should be about 1/2 inch higher than the gravel to help keep the small stones in place. If you need to tamp down the gravel, use a hand tamper.
What is the cheapest gravel for a driveway?
Crush and run
is one of the cheapest materials that can be used in a gravel driveway at about $0.40 per square foot. Cost per cubic yard is about $20 and per ton about $28.
How much will a ton of gravel cover?
A ton of gravel will cover
approximately 100 square feet, 2 inches deep
.
What is the best size gravel for a driveway?
A commonly used gravel size for driveway base layers is
#3 gravel
. This rock is generally 1-2 inches in diameter and does double duty by establishing a solid, reliable foundation and providing adequate drainage; both critical factors in driveway construction.
How many tons are in a 5 gallon bucket of gravel?
Regarding this, how many a 5 gallon bucket in a ton of gravel, a 5 gallon bucket of gravel yields 0.0375 tons weight, so 5 gallon buckets of gravel in 1 ton = 1/0.0375 = 27, so there are approx
27 buckets
of 5 gallon in a ton of gravel.
How much does pea gravel cost?
The general range for a cubic yard of plain pea gravel is about
$15 to $75
, and a ton will cost about $10 to $50. For a colored variety, expect to add an extra $20 to $50 to those prices.
How much pea gravel do I need for a fire pit?
You need
14.13 cubic feet
of gravel for the fire pit. Add 10 percent to the total to give yourself a little extra gravel in case you need it. Ten percent of 14.13 cubic feet is an additional 1.4 feet, bringing the total amount of gravel you need to 15.5 cubic feet.
What area will a 25kg bag of gravel cover?
For Decorative Gravel
As a rule of thumb 1 of our 25kg bags will cover an area of
0.25m
to a recommended depth of 50mm.
How deep should you lay gravel?
Decorative aggregates should be laid at a
depth of 50mm
. This ensures proper coverage without revealing the surface below. Laying the gravel too deep will mean you sink into the surface and it becomes difficult to walk across.
How many square feet will 5 tons of gravel cover?
Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel,
100 square feet per
ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.
