Simply add FTC Decarbonizer to the fuel, complete an oil change with Flushing Oil Concentrate and the problem is solved. “Seven years ago, our Detroit Series 60 developed blowby. Instead or rebuilding, we simply used FTC Decarbonizer and Flushing Oil Concentrate to clean up the internals and fix the problem.
What causes excessive crankcase Blowby?
When you combine a large cylinder bore, high cylinder pressure through turbocharging, many hours of use and marginal maintenance, excessive blowby is the result. The leakage of any combustion gases, air, or pressure into the engine’s crankcase is considered blowby.
How do I stop my engine from Blowby?
Engine blowby can be reduced by following 2 steps : Step 1 Simply add FTC Decarbonizer in with the diesel . Step 2 Use Flushing Oil Concentrate when completing an oil change. “To fix engine blow by, FTC Decarbonizer is added to the diesel at each fill, and you literally just drive the engine clean!
What causes oil blow by?
During combustion, high pressure on the top side of the piston pushes combustion gasses, as well as droplets of oil and fuel, past the piston rings and into the crankcase. This mixture is known as “blow-by.”
Can too much oil cause blow by?
If there is enough extra oil in the crankcase, it may be forced out through the piston seals and rings as the vehicle runs. This creates “blow-by,” which has the potential to coat your engine in oil. As the oil burns off, noxious fumes and gases are released.
How do you fix excessive oil consumption?
There are several ways to potentially reduce your engine oil consumption. If the cause of the high engine oil consumption is a leak around the piston rings, you may be able to have your piston rings replaced in order to prevent future leaks. Replacing the valve seals may also help to fix oil leaks.
Why is my car losing oil but no leak?
The engine must maintain a certain amount of oil to run efficiently and prevent engine destruction. If your car is losing oil but no leak or smoke, the problem is usually related to an internal oil leak that you don’t notice or important faulty components in your engine.
What are the 3 causes of oil consumption?
Causes of High Oil Consumption
Can you drive with bad piston rings?
You can drive your vehicle with bad piston rings for certain kilometres but you have to get it fixed as soon as possible or you will damage your engine. 1)The compression rings provide sealing above the piston and prevent the gas leakage from the combustion side.
Is it expensive to replace piston rings?
Piston ring replacement cost is between $1000 and $5000, depending on the car model and labor costs. The piston rings cost $40 to $200 depending on how many cylinders your car has. The labor work is between $1000 and $4000. Piston rings are small, but they are expensive to replace.
Can you just replace piston rings?
Replacing piston rings requires removing the pistons. To this effect, the cylinder head must be removed from the engine block, followed by the sump. After unscrewing the connecting rod ends, the pistons and the connecting rods can be removed from the top through the cylinder openings.
How do you replace piston rings without removing the engine?
because you cannot get the pistons out without removing the motor and tearing it down.
Can you remove Pistons without removing engine?
Signs your piston rings need replacing
When should I replace my piston rings?
just depends what the walls look liek once pistons are removed…if you can feel any grooves with ay fingernail, u need to bore it, if not, just get a fresh hone. I put low cr pistons in a d16y with 80k miles on block, and all it needed was a fresh hone.
Can I replace pistons without boring?
For an on spec jug, a proper hone job will not mean you need a new piston. Check your piston ring end gap and make sure its in spec.
Do you need new Pistons after honing?
Feel inside the bore and see if you can feel a “ridge” near the top of the bore. If you can, it will need bored, which means you will prolly have to bore it another .
