How Do I Know If My Mercruiser Starter Is Bad?

by | Last updated on January 24, 2024

, , , ,

The Symptoms of a bad boat starter are either boat won’t start (starts after turning the key multiple times), gives

grinding noise

, or buzzing noise like an alarm clock while starting the boat motor. However, some other elements also pose similar signs, but the starter could likely be the culprit.

How do you test a boat starter with a multimeter?

Step 1: Turn the dial of a digital multimeter

to the DC voltage setting

. Place the red probe on the positive battery post and then the black probe on the negative battery post. If the multimeter indicates the battery is producing less than 11.3 volts, recharge or replace the battery before testing the starter.

How do you test a starter on a Mercruiser?


Check the slave solenoid with a 12-volt test light first

. Clip the ground wire of the test light to the negative pole of the battery or metal part of the engine. With the key in the “Off” position, touch the point of the test light to each of the heavy wire terminals. One should be hot, the other cold.

How do you test a boat starter?


Turn your ignition switch to “Start” and read the voltage

. If the reading is more significant than 9.5 volts, try to start the engine. If this test fails, then your boat starter requires replacement or rebuilding. If the reading is less than 9.5 volts, you have a voltage loss between the battery and starter.

How do I check for a bad starter?

  1. A grinding noise. If the starter drive gear is worn out or does not properly engage, then you will hear a grinding sound. …
  2. Freewheeling. …
  3. Smoke. …
  4. Oil Soak. …
  5. Broken Solenoid.

Is there a difference between a Marine starter and a car starter?

The starter for a car looks exactly the same as the one you just removed from your marine engine. … A marine approved starter has

better seals and gaskets to keep water out

. It also contains more corrosive resistant materials.

How do you test a starter relay on a boat?

Turn on your multimeter and twist the selector knob to the nearest voltage

scale higher than 12 volts

. Test across the battery posts, being careful to touch the black (-) probe to the negative terminal and the red (+) lead to the positive terminal. The reading should be at least 12 volts.

How do you test a boat starter with jumper cables?

Connect one end of an oversize jumper cable —

12-gauge AWG

or larger — to the negative post of of the battery. Hold a vibration tachometer against the outside of the starter motor. Connect the jumper from the negative battery post to the starter casing. The starter will begin to run.

What causes a boat starter to go bad?


Water intrusion

is the #1 cause of starter failure. If water gets pumped into the motor portion of the starter from the flywheel, it will not drain out. Rust and corrosion will destroy the inside components of the starter. The #2 cause of starter failure is water ingestion into the engine.

What would cause a boat not to start?

Common Causes and Solutions for a Boat Engine That Won’t Start. … Boat engines need

ignition, fuel, air, compression and exhaust

to start up and run smoothly. If any of these elements are missing due to broken or damaged parts, your engine may not turn over and will have trouble starting.

How much is a starter for a boat?

How Much Does it Cost to Replace a Boat Starter? Inboard engine (and generator) starters cost from

$40 – over $1,000

depending on the engine. Outboard starters run from about $100 – $500. Skilled marine technicians charge from $75 – $150 per hour.

Can you jump a car with a bad starter?

Jump-starting a car with a bad starter motor

will not help start the engine

. Jump-starting will only boost battery power. A manual transmission car with a bad starter maybe push or tow started but an auto transmission car can not.

How do you tell if it’s your starter or ignition switch?

Test the Starter

It

is under the hood

, usually on the passenger side at the bottom of the motor next to the transmission. The ignition switch is a set of electrical contacts that activates the starter and usually is located on the steering column.

David Evans
Author
David Evans
David is a seasoned automotive enthusiast. He is a graduate of Mechanical Engineering and has a passion for all things related to cars and vehicles. With his extensive knowledge of cars and other vehicles, David is an authority in the industry.