Can you fit a hot tub through a regular door?
Yes, it really is possible to find hot tubs for groups of up to 6 people that will fit through a standard door
! Don’t expect these spas to be comfortable for large groups regularly, but hot tubbing as a small family—or the occasional social soak with guests or neighbors—will be totally doable.
Will a hot tub fit through a gate?
For an average-sized hot tub,
you will need a door frame that is at least 33 inches wide and 80 inches tall
. This is to ensure proper clearance. If you are currently constructing your home, install french doors in the room you want your hot tub to be in!
Do you need a flat surface for a hot tub?
It’s very important that a hot tub is installed on a completely flat surface
. This is because you need to ensure the weight of the spa is distributed evenly, so that the frame doesn’t shift or bow once it’s filled, or when it’s being used. If this happens, you risk damaging the spa and voiding the warranty.
How much access do you need for a hot tub?
The average size of a standard hot tub is approximately 2m square, allowing
some space around the hot tub is advisable
. We often recommend that you use a patio table and chairs to position where you think the hot tub would go to get a feel for the vol-ume of space required.
Does a hot tub have to sit on concrete?
A hot tub does not have to sit on concrete
and can be placed on any stable, level surface that will not become unstable due to moisture or weight. Those surfaces include wooden decks, paver stones, gravel beds, or spa pads.
Do you need access to all sides of hot tub?
Hot tubs need a minimum of 18 inches of access around all four sides
so repair technicians can replace fuses, service the heating elements, and clean out debris from clogged jets. Some hot tub models are carefully designed so that only one or two sides require access for maintenance.
How far should a hot tub be from the house?
Proximity to the house. To reduce the risk of electrocution, place your tub
at least 16 feet away from overhead power lines
. To protect your home and outbuildings from potential flooding, keep it at least 5 feet from any structure.
What is the best surface to put a hot tub on?
A concrete surface
is an excellent base for your hot tub as this material is extremely sturdy and long-lasting. If you have an existing patio made of concrete bricks, make sure it’s in good condition and is level (not angled for drainage). A customized poured concrete pad is an even better choice.
What surface does a hot tub need?
A hot tub requires
a stable surface — whether it’s a concrete slab, reinforced deck, or firmly compacted soil with crushed gravel
. There’s also the option to have the hot tub installed in the ground but that still requires a concrete vault.
Can you put hot tub on patio slabs?
Patio, Block Paving and Other Existing Stone Surface
Most patios, block paving and other surfaces are already reinforced and will be able to take the weight of a hot tub placement
.
Can you lift a hot tub over a fence?
If we just need to lift the hot tub over a fence or bush/trees and can park a vehicle on the other side, then
a HIAB crane may be just the trick
. This is a truck with a small crane on the back, and can be considerably more cost effective than a full size crane.
How do you hook up a hot tub to your house?
Start wiring at the LB fitting, and use fish tape to pull the wires through to the spa panel. Push the wires from the LB fitting into the house and to the breaker panel. Finally, use fish tape again to pull the wire through the conduit running from the spa panel to the control panel on the spa.
How much does it cost to install a hot tub UK?
At first, we like to mention that the minimum cost of installation will be
from £2500, up to £6000
. Many things will affect the cost of the installation, including the brand, type, and size.
Can you put a hot tub on brick pavers?
What can I put my hot tub on?
For outside installation, it’s recommended you place the spa on
a level, 4-inch thick concrete slab
. Other options include gravel, railroad ties, stepping or paving stones, and bricks. However, given the spa’s size, weight, and need for a level foundation, a strong, solid base is much preferred.
Can I put a hot tub on my patio?
Where should I put my hot tub?
You can put a hot tub on a deck, patio, under a gazebo, or anywhere else in your backyard (or indoors) that meets the foundational requirements
.
Should a hot tub be in the sun or shade?
Hot tubs should be in the shade
for three main reasons: it’s more comfortable than using the spa in direct sunlight, it means less wear and tear on your cover, and UV rays can reduce the effectiveness of your sanitizer.
Can you plug a hot tub into a regular outlet?
Voltage. The reason why
plug and play hot tubs can be plugged into a regular electrical outlet
is that they run on a standard 110 volt 15 to 20-amp household circuit – the same as your typical household outlet.
What do I need to know about installing a hot tub?
- Placement. Choosing that perfect spot for your new hot tub may not be as simple as you think. …
- Electrical Supply. …
- Space. …
- Privacy. …
- Safety. …
- Foundation.
Can a hot tub be up against a house?
While one of the major advantages of portable hot tubs is that they can be located almost anywhere,
it is often recommended that they are placed close to an entrance of your home
.
What are the rules for hot tubs?
Recommended guidelines suggest that you should
use a hot tub for 15 to 30 minutes at a time with a maximum of 45 minutes at any one time
. DO NOT EAT FOOD OR SMOKE IN THE TUB. DO NOT IMMERSE YOUR HEAD UNDERWATER. DO NOT PUT ANY WEIGHT ON THE PLASTIC LID AS IT MAY DAMAGE OR BREAK THE LID.
How often do you drain hot tub?
With average use, your hot tub should be drained and refilled about
once every three or four months
. But since everyone uses their hot tub differently, the answer can vary based on how many people use it and how often.
Can I put a hot tub on decking?
Yes, you can put a hot tub on a deck
. Decks built ground level up to 2 feet off the ground can support up to 100 lbs per square foot; sufficient for most hot tubs. But decks 2 feet or higher will need added support. The added support posts should be no more than 30′′ apart & ideally placed in poured concrete.
Should I put insulation under my hot tub?
Yes, it’s not hard to add additional insulation to a hot tub
. Less expensive hot tubs may have little to even no insulation, making them very energy inefficient. You can use a combination of rolled fiberglass, fiberglass panels, spray-on foam, and radiant barriers to significantly improve the energy-efficiency.
Can a hot tub sit on sand?
Hot Tub and Spa Base Pad
If you install your hot tub on sand, dirt, gravel, crushed rock or the grass, first, make sure the space is level, then simply put down this fantastic EZ Pad
. The EZ Pad is portable and does not require a town permit to install. Just make sure there is enough drainage below.
Are inflatable hot tubs worth the money?
Yes, with an average price of under $600, inflatable hot tubs are worth it for people who want a hot tub and are on a tight budget
. But in colder climates, know that the further below 50° F the outside air temperature is, the harder it is for inflatable hot tubs to maintain a water temperature of 104° F.
Can I put a hot tub on grass?
Can I put a hot tub on dirt or in the grass?
A hot tub should not be placed on soil or on a lawn
. Instead, it will need a solid platform to support all of the weight. Exposure to wet soil and grass will reduce the life of your hot tub and expose it to insects and moisture.
Where do you drain a hot tub?
Your hot tub comes equipped with a drain spigot, which is located
on the outside of the tub, near the bottom rim
. (Some models have two spigots, a primary and an auxiliary. The primary spigot is the one you’ll use to drain the hot tub; the auxiliary one is for bleeding the internal lines.)
What is the best foundation for a hot tub?
How thick should a concrete slab be to hold a hot tub?
The minimum thickness safety requirement for a basic hot tub pad is
4′′
thick reinforced concrete with a diameter of 6′′ less than the diameter of the bottom of the tub. Therefore, a 5′ round straight sided wood hot tub would require a 4′ 6′′ square pad.
Can a hot tub be placed directly on the ground?
Outdoor hot tub placement, such as decks, concrete or brick patios, is common. However, the hot tub can be placed on any solid, uniform, level surface.
Do not place your hot tub on grass or bare ground
.
How heavy is an empty 6 person hot tub?
Can you crane a hot tub over a house?
With the help of a crane, you can lift a hot tub onto balconies or rooftops, over fences or garages… even over your house
. The good news is that hot tubs are easy work for crane operators. They are not heavy compared to most crane jobs, and it’s a quick operation (the actual lift only takes a few minutes).
How do you put a hot tub in your backyard?
- Have Your Hot Tub Delivered to Your Home. Most retailers will deliver your new hot tub directly to your home. …
- Place and Position the Hot Tub. …
- Assemble the Hot Tub. …
- Fill your Hot Tub. …
- Turn on Your Hot Tub. …
- Add Sanitizing Chemicals. …
- Enjoy Your New Hot Tub.
Are plug and play hot tubs any good?
Plug and play spas,
draw less power, but take much longer to heat the water
. This means that the hardwired spa will be the more efficient option as the short-term, high-heat it provides will use less energy overall vs the plug and play longer-time, lower-heat approach.
How much electricity does a hot tub use?
Hot tubs run on an electrical supply. They usually need
between 13 and 40 AMPS
of power to run. The electricity powers the heater, pumps, lights and all the other working components on the hot tub. It’s usually recommended that hot tubs run 24/7.
