Life Member.
Yes, you can move your PCV to the other bike as both bikes use the same one
(Part # 15-011). You will however need to go to the Power Commander website and download a new map to the PCV that matches your current setup for the 2012.
How do I reset my power commander?
To reset the throttle position
click on “Power Commander Tools” and then select “Set Throttle Position
. To reset both the closed and open throttle positions, first make sure that the bike is communicating to the computer, then click on “Reset”. Twist the throttle wide open and release. Now click OK.
Is Power Commander plug and play?
Featuring a plug-and-play kit
, Power Commander V can be installed discreetly underneath your seat, ensuring your ride looks as good as it runs.
Are power commanders worth it?
Do you need to dyno tune a Power Commander?
yes you need a powercommander for a dyno tune
. That is what they tune that controls how much fuel is pumped into your engine. You also should install block off plates. It may help with some of the popping as well.
How much HP does Power Commander add?
The Power Commander is a tuning tool to adjust fuel, and on some models ignition timing. Just adding a Power Commander to a completely stock vehicle
usually does not increase peak horsepower
. It usually will improve drivability, throttle response, and mid-range horsepower and torque.
Will a Power Commander lose its map?
If you disconnect the battery or disconnect the Power Commander from the bike it will not lose the map
. The only way to lose the map is to download another map to the unit.
How do you program a Dynojet Power Commander?
How do you set up a Power Commander?
Can a Power Commander hurt a motorcycle?
Registered.
Power Commanders do not harm your bike
. They don’t “trick” the OEM ECU. It is nothing more than a piggyback ECU.
What do power commanders do for motorcycles?
A Power Commander is a brand of fuel injection or ignition timing manufactured by Dynojet Research Inc. The Power Commander is used by motorcycles as a way of
boosting their engine performance to a higher level of horsepower than a rider might get from the motorcycle’s stock engine performance
.
What’s the difference between Power Commander 3 and 5?
How much does it cost for a dyno tune?
Costs to Tune a Car
Taking your car to a dyno tuning garage is the best way to not only improve performance, boost horsepower, and make the engine run more efficiently. However, initial costs can start at
$400 to $700
.
How long does it take to dyno tune a motorcycle?
The cost is dependent on the time it would take to tune the motorcycle.
Fuel-injected motorcycles typically take four hours. Carbureted motorcycles typically take two hours
, due to the fact that there are fewer adjustments that can be made on carburetor engines.
Does a dyno tune increase HP?
A tune to a dyno will probably increase your horsepower by 10-15 percent if you are driving a stock car
. The performance parts you equip with, such as exhaust and turbo, can increase your horsepower by 50 horsepower – even more depending on your engine and the parts you choose.
How much HP does Power Commander add to motorcycle?
Registered. SteveMcqueen said: a full system with a power commander should be good for around
115-118 Hp
on the 04…
Can you put a Power Commander on a car?
Yes
. we have simple options like the Power commander, for cars.
Do I need a Power Commander with a full exhaust?
the only time you need mapping (power commander) is if you do anything to change the air/fuel ratio
. the reason a slip-on does not need a power commander is because the exup valve (a servo controlled butterfly valve in your exhaust) is still in place and it manages exhaust flow and back pressure.
Can I unplug my Power Commander?
I have a Power Commander II on my TLS. It simple goes inbetween the ECU connector and the ECU. To disconnect it all you have to do is
un-plug it from the ECU then plug the main ECU connector back into the ECU
.
Does dynojet have an app?
About Dynojet C3 Mobile
Dynojet C3 Mobile is a free app for Android
published in the System Maintenance list of apps, part of System Utilities. The company that develops Dynojet C3 Mobile is Dynojet Research, Inc. The latest version released by its developer is 1.0.
Does Power Commander adjust timing?
Your Power Commander has optimized your fuel ratio for better performance, now update your spark advance curve with our Ignition Module. This easy to install device
can change timing in each individual cylinder
and is one more way that you can get your vehicle to push the limit.
How do I download dynojet maps?
To install a map on a Power Commander V fuel tuner, you will need to download the Dynojet Power Commander software using a Windows computer (or a Mac running Windows). Once you install the software, it is easy to download maps
from the Dynojet.com website
.
