Can you refill Worx trimmer spool? The diameter of this line is approximately 0.065” . The line is pre-wound on spools specially designed to work on Worx 20V and 32V battery operated trimmers.
How do you feed the line on a WORX trimmer?
What size line does the Worx trimmer use?
The diameter of this line is approximately 0.065” . The line is pre-wound on spools specially designed to work on Worx 20V and 32V battery operated trimmers.
How do you reload the trimmer spool?
Why does my Worx Trimmer line keep breaking?
The line breaks repeatedly creating a VERY frustrating ordeal. The reason... the cord is not wound evenly about the spindle, consequently the auto release feature does not work properly . Hence, the line does not advance and breaks inside the spindle. Save yourself and buy the cord and wind it yourself.
How does auto feed trimmer work?
How do you turn the WORX trimmer into an edger?
How do I replace trimmer line?
Where is the model number on a WORX trimmer?
Can you use any strimmer wire?
You can normally fit thinner strimmer line into you strimmer too . So for example if you have 2.4mm requirement, you can probably fit 2mm but I highly recommend using the correct gauge for safety and product efficiency.
How long should the trimmer line be?
The length to which the lines should be cut also varies, from around 10′ to 25′ . If you are not sure, err on the side of too long; you can always cut it shorter later. Both lines should be cut to the same length. Make sure your trimmer’s engine is turned off.
How do you rewind a dual line trimmer?
Should you soak your trimmer line in water?
Trimmer line does tend to dry out over time and becomes more brittle. Storing it or soaking it in water will help reduce line breakage and make the line more flexible . Be sure to deplete your supply of last year’s line before you purchase new line and begin using it.
Why does my trimmer line melt together?
Trimmer line can melt together because of several reasons, here are a few. Heat created by continually trimming around fences, and or bricks . Take breaks and feed line often. Heat created by continually trimming around concrete and or asphalt.
How do I stop my Trimmer line from breaking?
- Check the quality of the trimmer line you’re using.
- Check your trimmer line is thick enough.
- Be careful around hard surfaces.
- Make sure your line is not past its best (old).
- Make sure the trimmer line (+trimmer) is designed for the trimming you’re doing.
Is bump feed or auto feed better?
Line Feeding
The automatic-feeding system draws out more line only when it reaches a certain shortness. While the bump feeder is quicker , it also uses up a lot more line, which can add up in the cost department, and the time needed to replace the line.
Is Thicker trimmer line better?
Low-voltage (up 24 volts) and small gas-powered trimmers (20 cc) work best with medium or small-sized trimmer lines. Thicker lines need more powerful engines that spin fast enough for the trimmer lines to cut through grass and weeds .
How do you bump feed a string trimmer?
Where are Worx tools made?
Now, remember that Worx is owned by the Positec Tool Corporation, and yes, they make all of their products in China . Although you might be worried about tool quality issues due to the location of manufacturing, most would agree that Worx tools are some of the better ones to come out of China.
How do you remove the head of a WORX trimmer?
How do you clean Worx grass trimmers?
Wipe the trimmer parts down with a rag after use and before storing it. Do a deeper cleaning with a stiff brush and a damp cloth periodically. Use cotton swabs, lightly dampened with machine oil to clean exhausts and intakes and other hard-to-clean areas.
How do I find my Worx model number?
- Warranty Statement. ...
- Terms. ...
- Product registration.
What is the difference between WA0004 and WA0010?
You can find spools that fit the WG124 here. What’s the difference between this and the Free Spools For Life package (WA0010)? This model (WA0004) is a two-pack of spools . Our Free Spools for Life package (WA0010) is a benefit for customers who have taken advantage of a special TV or internet offer from Worx.
Where is the model number on a Ryobi trimmer?
Where can I find the model number and serial number of my Outdoor Product? Information on your RYOBI product can be found on the black label located directly on your tool . Your serial number can be found on this label and may begin with CS, OA etc. Your model number will either begin with a RY or a P or AC (accessory).
Does it matter what trimmer line you use?
This probably comes as no surprise to anyone, but the general rule with string trimmer line size is that the tougher the application, the thicker the line needs to be . A larger diameter line increases the power and durability of the line, which leads to less breakage and wear-out.
What else can you use instead of strimmer wire?
Just use cheap cable ties instead.
Why does my strimmer line keep jamming?
Replace the line with one having the correct diameter
Subsequently, it will jam if you have replaced it with one that’s too thick . The best place to confirm the right diameter for your unit is once again the operator’s manual. Go through it and note the recommended diameter and order one that’s right.
How often do you replace trimmer line?
You should replace trimmer string spools once every 90 to 180 days if you use the trimmer weekly . Overusing the trimmer string greatly increases the chance of it breaking while you’re using it. If you don’t replace it often enough, the ends will fray, and it won’t chop through the weeds.
Does trimmer line get brittle with age?
Are all trimmer lines the same?
But in general, there are 4 different types of trimmer line :
Twisted, Star-shaped, And Multi-sided (square, triangle, etc).
How do you extend the cord on a strimmer?
Can trimmer string spoil?
How long should I soak trimmer line in water?
STIHL TIP: Soak your trimmer line in water for 24 hours before re-spooling your trimmer to keep it flexible!
How do you store a whipper snipper cord?
To keep a mowing line elastic, remove the spool from the mowing head and store it in a damp place . Two or three days before the start of the new season, place the line in water to keep it flexible and supple (this also applies to the PolyCut blade).
Is Worx the same as Black and Decker?
What can be said here is that Black & Decker is a much larger company than Worx and it does make many more products. For example, Worx makes a good deal of lawn and outdoor equipment, some power tools, and various accessories.
Do Worx batteries work with Black and Decker?
Free shipping to Canada and United States. This battery adapter allow you to use Black and Decker 20V batteries on WORX 20V tools (sold in Canada and USA with 6 Pins).
