Can You Replace Fixed Fork With Shock On Mountain Bike?

by | Last updated on January 24, 2024

, , , ,

Undo your stem bolts. Remove the top cap making sure you are holding onto the fork. As soon as you undo the top cap, your fork will want to fall out of the frame. Slide off the stem, and slide the fork out of the frame.

Can you change front forks on a mountain bike?


Pretty much the biggest upgrade you can give your mountain bike is a new fork

but the installation can seem daunting even to experienced MTB tinkerers.

Can you put a shock on a mountain bike?

Aside from downhill bikes and some cheaper MTBs, most cross-country, trail and all-mountain bikes rely on air springs. As a result

it’s relatively easy to fine-tune the amount of sag on your bike

. All you’ll need is a shock pump, a ruler/tape measure or verniers and perhaps a small cable tie.

Can you put a rigid fork on a mountain bike?

If you live in an area with wide-open terrain or very smooth trails, the rigid fork can also deliver a unique riding experience. Unlike the original 1970s mountain bikes, which only had steel forks with cantilever brakes,

modern rigids ride a variety of steel or composite forks and are compatible with disc brakes

.

Can you put a suspension fork on a road bike?

Rear shocks and suspension forks are the norm on mountain bikes, but

their design is of limited use for road bikes

. A fork (or shock) would negatively affect the weight and the performance of a road bike and it would noticeably change the geometry of the bike during compression.

Can you put 29 inch wheels on a 27.5 fork?

Condensed answer:

Some 27.5-inch forks have the clearance to accept a 29-inch wheel

. However, the conversion makes the gap between the tire and fork’s arch noticeably smaller. As a result, the tire starts throwing more small stones and debris against the arch.

Are MTB forks universal?


Any standard 1 1/8 29 fork will work

.

How do I upgrade my mountain bike forks?

How do I add air to my mountain bike forks?

What PSI should my MTB shock be?

Often yes, usually rear shocks run

100-200psi

, but fork psi varies a lot, depending on the design. Get the sag around 25% (maybe slightly less sag in the front than the rear) and see how it rides (that’s what really matters), adjust on the trail as needed.

What PSI should my mountain bike forks be?


Start with the recommended air pressure for your weight. If that is not known, try 100psi

. On this fork it said l should be running 75psi for my weight but there was always about 30mm unused travel. I dropped the pressure by 5psi, then another 5psi, ending up at 65psi.

Can you put a 27.5 fork on a 26 frame?

Condensed answer:

A 26-inch wheel can be easily installed on a 27.5 fork if both are disc brake ready

. If the fork uses rim brakes, however, the braze-ons would be a bit higher, and the calipers won’t catch the rim.

How do you fix front shocks on a mountain bike?

Can you replace bike forks?


Replacing your fork can up your bikes performance, and buying is the easy part

. The real issue lies in how to remove and replace your old one. Below, is a step-by-step guide to help you through this process.

Which is better rigid fork or air fork?


If your ride is mostly on good-quality paved roads, a rigid fork is more practical

. Entry-level bikes with suspension forks can actually cause more headaches and be more dangerous than the benefits they offer.

Why use a rigid fork on a mountain bike?

A rigid fork

eliminates fork dive, allowing rigid bikes to rail turns like never before

. You will also experience increased bar sensitivity, as well as become more in tune with the trail. As your bike handling skills improve you will find new features and alternate lines that you had just plowed over before.

Can I use rigid fork on trails?

It probably depends a lot on the terrain you ride and how much abuse you want to take. If you ride very rocky and rooty terrain, the suspension is definitely nice. From your description,

you’d probably be fine on a rigid

. In the end though, if you can afford the extra $$, I’d recommend at least front susp.

Why do road bikes have no suspension?

Road bikes are meant for one thing, to get from point A to point B in a quick manner. So one of the major reasons that road bikes don’t have suspension is

because of the added weight

. Suspension is a heavy component on a bike, and those added pounds just aren’t conducive to what road bikes are meant to do.

Do carbon forks absorb shock?


Carbon fibre frames and forks don’t have the same amount of travel (shock absorbing capability) as shocks

.

Does suspension make a bike slower?


Slows the bike down on climbs

– high quality suspension usually has a lock-out option, when it doesn’t slow the bike down too much, but even when locked, it’s not completely rigid, and it’s still heavier – which doesn’t help with riding up hills.

What is the advantage of 29 inch wheels on a mountain bike?

29” Wheel Advantages


29” wheels often feel smoother to ride due to the higher air volume in their larger tires

. The extra air volume acts as additional suspension – some say that it feels like having an extra inch of travel to ride the bigger wheels.

What is the difference between a 27.5 and 29 fork?


29-inch forks are built with a longer offset than their 27.5-inch counterparts

, which means that 29ers require a steeper head angle to achieve the same trail measurement. A more kicked-out head angle yields a bike with greater pitch stability, or fore-aft stability.

Can I convert my 26er to a 29er?


Yes, it is possible to mount 29 inch (29er) wheels onto a modified full suspension 26” mountain bike frame

.

Can you put a 130mm fork on a 100mm bike?


at 130mm you’ll probably be fine, I wouldn’t put anything bigger on there

. The kona frames are pretty strong, I used to run a 130mm fork on my 100mm jump bike for AM and a lottle more FR riding, I was fine.

Can you put a 120mm fork on a 100mm bike?

For all around riding,

should be fine

, but you may notice it’s a bit harder to keep the front wheel down on the steep uphills.

How do I know if my fork is compatible?

David Evans
Author
David Evans
David is a seasoned automotive enthusiast. He is a graduate of Mechanical Engineering and has a passion for all things related to cars and vehicles. With his extensive knowledge of cars and other vehicles, David is an authority in the industry.