Can You Sand ModWood?

Can you sand ModWood?

The brushed finish can be wire-brushed or lightly sanded with coarse sandpaper

to remove scratches.

How do you get stains out of ModWood?

Stubborn (usually oil-based) stains can be difficult to remove – we find that

water-diluted Deck Protect Composite Clean or So Safe deck cleaning products

effective. The use of Kenco degreaser works well for heavy spot stains – scrub in and wash off after a few minutes.

Can I paint ModWood?

Most people do not use any coatings on ModWood, however

it can be painted or stained at a later date should this be desired

. Deck Protect Composite Refresh is a rejuvenating stain and it is available in the ModWood colours. In all circumstances you must follow instructions as stated on the packaging.

Can ModWood be bent?

Is ModWood capped?

ModWood XTREME GUARD®

The capping is incorporated on ALL 4 faces

making it super durable. Manufactured to the highest achievable level of slip resistance P5 (AS 4586:2013), making it ideal for wet surfaces and commercial decks.

How do you refresh composite decking?

1. Step 1: Pre-spray your deck. …
2. Step 2: Spray with soapy water & scrub. …
3. Step 3: Rinse thoroughly. …
4. Step 1: Pre-rinse. …
5. Step 2: Mix up your vinegar solution. …
6. Step 3: Sprinkle baking soda. …
7. Step 4: Rinse thoroughly.

How do you clean dirt off a composite deck?

Spray deck with soap, then follow by gently scrubbing each deck board with a soft bristle brush

. Spray/rinse each individual deck board using a fan tip no closer than 8-in (203 mm) from the decking surface. RINSE THOROUGHLY. If dirty water from cleaning is left to dry, a film will remain on the decking surface.

Can you screw into ModWood?

ModWood must not be used as part of the frame or used as a structural element.

12 gauge screws may be used on 137mm boards only

. Fasteners must not be located closer than 20mm from board ends. This will necessitate double joist or laminating a block on these joists where end butt joins will be located.

What is ModWood made out of?

ModWood is an Australian made and owned composite product made essentially from

a mixture of ground sustainable wood waste and plastic

(we actually use recycled plastic milk bottles). ModWood products contain no formaldehydes.

Does ModWood expand?

As ModWood

expands in heat and sun

, to avoid building stress into your deck and having possible lengthways shrinkage, it is best to fix your decking boards when the ambient temperature is less than 25 degrees celsius and when the boards are not sitting in full sun.

Can you curve composite decking?

Composite decking is flexible enough to be bent across curved sections of the deck

. If the decking is hot it will be even easier to bend into the desired shapes.

Can you glue ModWood?

Construction Adhesives when used with ModWood and KlevaKlip:

As one of the base ingredients in ModWood is High Density Polyethylene (HDPE), the adherence of many construction adhesives to ModWood is nowhere near as strong as they are to timber. However,

some adhesives have been shown to still have some adherence

.

What is the best composite decking in Australia?

1. Composite Prime HD Deck Dual. Best reversible colour composite decking: eco-conscious and a great natural look. …
2. Homebase Ecodek Composite Deck Kit. …
3. Trex Transcend Composite Square Edge Decking Board. …
4. B&Q Neva Anthracite Grey Composite Deck Board. …
5. Havwoods Trekker New Oak Decking.

Is ModWood fire rated?

Where is ModWood decking made?

In a world where most composite decking products are imported from countries that have a different climate to our harsh conditions, ModWood Technologies P/L is an Australian owned company, manufacturing with

Australian product in Australia

, since 2001; for Australian conditions.

When was ModWood invented?

ModWood was first produced in Australia in

2000

and the product has undergone continuous development. In 2008 the introduction of a wood grain finish created a more wood-like appearance that appealed to the market and the full range now carries the grain pattern.

Can composite wood be sanded?

After the composite is fairly smooth, switch to 800 grit sandpaper and sand until the composite is very smooth.

You can use an orbital sander or sand by hand

. Use a dry rag and acetone to remove dust, grease, and debris. Apply a primer.

What can I do with faded composite decking?

If your wood rich composite decking is looking faded and worn, it’s time for a refresh!

The RockSolid Composite Deck Refresh product line is an all encompassing solution

. Our stain remover and cleaner work great at cleaning and preparing the surface of your composite deck for the refresh toner.

How do I get the shine back on my composite deck?

Can you scrub composite decking?

Use a soft bristle brush to scrub the decking

(or a pressure sprayer) to loosen any trapped dirt and debris between the joints and remove any mold or grease. Hose off and dry down and enjoy your newly cleaned composite decking.

What is the best thing to clean composite decking?

When it comes to cleaning decking, we recommend

a basic cleaning with a composite deck cleaner or combination of soap, hot water and a soft bristle brush

. Ideal times for cleaning decking are just after installation and then on a semi-annual basis (typically spring or autumn is most conducive with the weather).

Can you jet wash composite decking?

Can composite decking be power-washed?

Yes, it is safe to clean TimberTech composite decking with a power washer

.

Can you nail ModWood?

ModWood only recommends dome-head nails, designed for the head to sit primarily at the surface of the board, rather than under it

. Other types of nails will void your ModWood warranty. It is essential to pre-drill when fixing within 50mm of the end of the board. You will need to hand nail these fasteners.

Can you lay ModWood on concrete?

Subject to local building codes,

ModWood decking may be fixed over concrete, provided the concrete is in good condition and there is adequate “fall” to assist drainage

.

Can you top fix Ekodeck?

Once you reach the end of your deck, you may need to rip the last board down to fit.

Secure the last edge of your board by top fixing using 10g 65mm screws

. Be sure to pre-drill and pre-countersink the board.

How long do composite decks last?

Composite decking requires minimal upkeep and can last

between 25 and 30 years

. On average, plastic decking has a similar lifespan to composite decking and can last nearly 30 years.

Does composite decking need maintenance?

NeoTimber recommend a routine clean of your decking every 3-6 months

to clear away dirt, mud and soil that can accumulate and sit on your boards over the course of time. For a general clean – we recommend applying warm soapy water to the surface of the boards and cleaning with a soft bristled brush.

What is ModWood used for?

ModWood has revolutionised the look and feel of outdoor areas. Highly versatile, ModWood blends beautifully with any architectural style. From

decking to screening to commercial outdoor areas

, ModWood creates very practical yet stylish outdoor living spaces that are also environmentally friendly.

What temperature can you bend composite decking?

Can you bend composite board?

The aluminum composite panel is a very flexible material. As mentioned earlier,

you can bend an aluminum composite panel, but it requires special tools

. Therefore, for safety procedures and a better result, it’s always recommended to contact your supplier for doing the bending process.

How do you cut composite decking curves?

Does Ekodeck scratch?

What is millboard decking?

Millboard is

the finest wood-look composite decking and composite cladding

, enhancing outdoor spaces with enduring distinction. Hand-moulded from the finest pieces of oak, it boasts refined timber grain that mimics natural timber but is engineered to offer an enhanced decking experience.Why choose Millboard.

What is Hardie deck?

HardieDeckTM decking is

made from James Hardie’s premium fibre cement

. It creates a clean look to connect a stylish interior environment with the outdoors, without risking damage from the elements. Smooth, wide gap-free boards and freedom of colour choice makes this cement decking a stunning outdoor floor.

How do you get stains out of wood without sanding?

1. Liquid and gel strippers soak into the finish to loosen it, and heat guns work by softening it; both methods require scraping. …
2. Liquid and gel strippers are brushed on, and an inexpensive, natural-fiber craft paintbrush works as well as an expensive brush.

Does baking soda remove oil stains from wood?

Begin by pouring a pile of absorbent powder, such as baking soda or sawdust, over the stain until it is about 1/4 inch thick. Leave the powder on the stain for several hours or overnight. Sweep or vacuum up the powder. If any stain remains, repeat the steps above as many times as needed to fully remove the stain.