Does Ford Use Dana Axles? - Fixanswer - Get your knowledge fix!

The Dana 60, a heavier-duty axle than the Dana 44, was first used in the 1950s. It was the axle of choice under countless

Dodge, Ford, GM, Studebaker, IH and Jeep 3/4-ton and 1-ton fullsize trucks, as well as Ramchargers and Trail Dusters with the 440ci V-8, and some heavy-duty 1/2-ton Ford and IH trucks

.

When did Ford stop using the Dana 50?

Bolted under the front of the Super Duty well into the middle of 2002, and equipped on most 4×4 Ford Excursions, the Dana 50 front axle was a carry-over axle that Ford finally phased out officially

by the end of 2003

.

When did Ford use Dana 50?

What trucks use Dana axles?

A Brand Name Synonymous With Axles. Dana components are found in the

Ford Model T, the original Willys Jeep, London taxis, 18-wheelers, earth-moving machinery, and NASCAR racers

.

What years did Ford use Dana 60?

Ford uses Dana Super 60 Front Driving Axles in

2005 and newer

F250, F350, F450, and F550 Super Duty 4×4 trucks. Each axle is built with a Bill of Material (BOM) Tag affixed to the differential…

Is Dana 44 better than 60?

Like we said above,

the Dana 60 is the stronger axle

. If you want to run big tires or big power you need a Dana 60 axle. At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling.

Does f150 have solid front axle?

Only the F-350 from 85.5 up came with a solid front axle from the factory

. All F-150’s, 250’s and 85.5 down 350’s had the TTB independant front suspension (150’s had coil springs while the 250’s and 350’s had leafs).

Which trucks have solid front axles?

The only full-size trucks with a solid front axle are

Ram’s heavy-duty lineup and Ford’s Super Duty trucks

. Every half-ton truck uses independent front suspension. But there’s still one midsize truck with a solid front axle: the Jeep Gladiator.

What axles are in a Ford Excursion?

2000-2005 Ford Excursion 4x4s use

Dana 50 monobeam front axles

. Externally, the Model 50 Axle looks almost exactly like a Dana 60 used on most of the Super Duty 4x4s of the same vintage, however, all the internal differential components are substantially smaller.

What axle is in a 97 F250?

Eighth and ninth generation (1986-1997) Ford Super Duty trucks use the

Ford Sterling 10.25 axle

. This was the only axle offered with these trucks.

What does a Dana 80 come in?

ID A Dana 80 Rear Axle in

Chevy, Dodge Ram, or Ford Truck

IDN-126. Was: Dana 80 Rear Axles have been in production since the 1988 Model Year. They have been used in Chevy/GMC 1992-2002 , Dodge(1994-2002), and Ford (1988-current) trucks vans, and motorhome chassis.

What are Dana 44 axles?

The Dana 44 is an

automotive axle manufactured by Dana Holding Corporation

and is used among automobile manufacturers and in the automotive aftermarket area as well.

What vehicles have a Ford 8.8 rear end?

1986-2014 Ford Mustang.
1982-2012 Ford F-150.
1982-1996 Ford Bronco.
2001-2005 Ford Explorer Sport Trac.
1991-2011 Ford Ranger 4.0L models.
1991-2001 Ford Explorer (Solid axle)
1985-2011 Ford Panther platform vehicles.
2012–Present Ford F-150 (Super 8.8, depending on engine and other options)

What vehicles have a Dana 35?

The Dana 35 (as well as the AMC-15) are found in a wide variety of vehicles; the most common Dana 35 applications are as a rear axle in the

Jeep Cherokee, Jeep Wrangler and Jeep Comanche

. It also is a common front axle in the Ford Explorer. In the 1990s Ford used the Dana 35 as a front axle.

Is a Dana 70 better than a Dana 60?

The torque rating for a stock Dana 70 axle shaft is 8966 ft/lbs, which is

almost 50% stronger than the stock Dana 60 axle shaft

, which has a rating of 6044 ft/lbs.

What Ford trucks came with a Dana 60?

1974–1979 F-250 (optional)
1999–2011 F-250 (optional)
1979, 1986-2011 F-350 (optional)
2000–2004 F-450/F-550.

How do you tell if an axle is a Dana 60?

How do you tell if you have a Dana 60 or 70?

How big of a tire can a Dana 44 handle?

We often get asked how big a tire a Dana 44 can hold up to. That’s not an easy question to answer. Several factors, such as terrain, vehicle weight, driving style, and engine output, come into play. However, as a very general rule,

a 36-inch tire is about the limit for a Dana 44

.

How do I know if I have a Dana 30 or Dana 44?

Dana 30: This axle size is the most common, and you’ll only find it on the front of Jeep. …
Dana 35: This was an axle size used on most Jeep rear axles. …
Dana 44: These are the beefier axles found on the rear of all Wrangler models now with either a 3.21 or 3.73 gear ratio.

How much horsepower can a Dana 60 handle?

Additionally, the Dana 60 (S60) from Strange comes equipped with their beefy 35-spline alloy axles and carrier that can handle

over 1,000 horsepower

. A vintage Dana 60 like ours with its stock 23-spline axles and clutch-type Sure-Grip is limited to roughly 700 horsepower of sticky tire, strip action.

Does F250 have solid front axle?

When did Ford stop using Twin I Beam suspension?

Twin I-Beams and Twin Traction Beams were utilized on various F-Series trucks until

2002

.

What axles are in the new Bronco?

Four-wheel drive comes standard with either a base 2-speed transfer case with shift-on-the-fly capability, or a more rugged version with a

Dana 44 solid rear axle

and available front and rear lockers.

What is the most reliable 4×4 of all time?

Jeep Wrangler. Jeep says the new model is the best Wrangler yet, but they’ve all been pretty good. …
Daihatsu Fourtrak. …
Toyota Land Cruiser. …
Range Rover. …
Mercedes G-Wagen. …
Land Rover Defender. …
Jeep Cherokee. …
Suzuki Jimny.

Is the new Bronco solid axle?

What is the best 4×4 in the world?

Jeep Wrangler. Jeep doesn’t revitalise the Wrangler very often, but the latest generation is more useable than ever on the road as well as more capable off it. …
Toyota Land Cruiser. …
Mercedes-Benz G-Class. …
Ford Ranger Raptor. …
Land Rover Discovery. …
Bowler Bulldog. …
Suzuki Jimny. …
Ford Bronco.

Is the excursion a 1 ton?

What front axle is in a 2003 F250?

What front axle is in a 1999 f350?

When the 1999 Ford F-250 and F-350 Super Duty® trucks were first introduced, all the Single Rear Wheel (SRW) models used a

Dana-Spicer Model 50 monobeam

front axle.

What axle does my f250 have?

What is a Ford Sterling axle?

The Sterling 10.5 axle is

an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI

. It was first used in model year 1985 Ford trucks. The axle was developed to replace the Dana 60 and Dana 70. The Sterling 10.5 axle is currently only made as a full floating axle.

Is a sterling 10.25 a 1 ton axle?

Strapped under many 3/4- and 1-ton Ford pickups

are rear axles that are somewhat mysterious. Often referred to as the Sterling 10.25- or 10.50-inch axles, they’ve been used in the vast majority of aforementioned trucks since the mid-’80s, yet most folks don’t know much about them.

What truck has a Dana 80?

Ford was the first company to use the Dana 80; it is used

mostly in trucks with dual rear wheels with the exception being some Dodge 2500’s and select Ford F-350’s

. The Dana 80 has a gross weight rating up to 11,000 lbs, however it is common practice among manufacturers to derate Dana 80’s.

Is a Dana 80 a 1 ton axle?

The Dana 80 is only rated for 1 ton trucks

, not a 2.5 ton truck.