Does Home Depot Carry Kidde Smoke Alarms?

How much does a Kidde smoke detector cost?

Is there a recall on Kidde smoke detectors?

The recalled units are part of Kidde Model Series 2040, 2050, 2060 and 2070 Smoke and Combination Smoke/Carbon Monoxide alarms. However, only alarms with the “TruSense” logo or

“AMBER=FAULT” printed on the front of the alarm are included in the

recall. The model number is printed on the back of the alarm.

How long is a Kidde smoke detector good for?

In accordance with the National Fire Protection Association (NFPA), Kidde recommends replacing smoke and heat alarms every

ten years

, and replacing carbon monoxide and combination alarms every seven to ten years (depending on your model) to benefit from the latest technology upgrades.

Why is my Kidde smoke alarm going off for no reason?

False alarms are most commonly caused by something interfering with the sensor. To clean, after disconnecting the alarm and removing any removable battery: hold

the unit

by its edge and thoroughly blow through the gap on the side of the unit with compressed air (like keyboard cleaner).

When should I replace my Kidde smoke detector battery?

Kidde recommends replacing the batteries in all of your alarms at

least once a year

, or any time the unit indicates that the battery is low. The general rule is to replace the battery twice a year: once when you switch to daylight savings time, and once when you switch back to daylight standard time.

How do I check my Kidde recall status?

Q: How can I find out if my fire extinguisher is included in the recall? A: Please

contact us at (855) 271-0773

between 8:30 a.m. and 5 p.m. EST Monday-Friday (excluding holidays), or between 9 a.m. and 3 p.m. during the weekend to determine whether your extinguishers are affected.

How do you stop a hardwired smoke detector from beeping Kidde?

1. Turn off the power to the smoke alarm at the circuit breaker.
2. Remove the smoke alarm from the mounting bracket and disconnect the power.
3. Remove the battery.
4. Press and hold the test button for at least 15 seconds. …
5. Reconnect the power and reinstall the battery.

Where is the replace by date on Kidde smoke alarm?

The manufacture date code is

stamped on the label located on the back of the alarm

.

Do you really need to replace smoke detectors every 10 years?

10 Years Smoke Alarm Requirements

Smoke alarms have a limited lifespan. The National Fire Protection Association

(NFPA) recommends every smoke alarm be replaced after 10 years

and that regular batteries be replaced every six months.

Why is the red light flashing on my Kidde smoke detector?

The red LED (located under the TEST/Hush button) has four modes of operation: Standby Condition: The red LED

will flash every 40 seconds to indicate that the smoke alarm is operating properly

. … The flashing LED and pulsating alarm will continue until the air is cleared.

How do I test my Kidde smoke alarm?

You can test your smoke alarm by

pushing the Test/Hush button on the cover and holding it down for a minimum of 5 seconds

. This will sound the alarm if the electronic circuitry, horn and battery are working.

Why do smoke alarms go off in the middle of the night?

As a smoke alarm’s battery nears the end of its life, the

amount of power it produces causes an internal resistance

. … Most homes are the coolest between 2 a.m. and 6 a.m. That’s why the alarm may sound a low-battery chirp in the middle of the night, and then stop when the home warms up a few degrees.

Why is my smoke alarm going off after I changed the battery?

It is normal for smoke alarms to go off and sound briefly (up to 5-10 seconds) when you install a new battery or when they are powered up. If the alarm continues to go off and no smoke is present, the cause may be one of the following:

There may be insufficient battery power, try new batteries

.

Why is a red light flashing every 13 seconds on my smoke detector?

All smoke detector units blink red briefly every 40-60 seconds to indicate that they are in operation. However, if your smoke detector is flashing every 13 seconds, it means

you may have dust inside the cover unit

.

Why is my smoke alarm chirping if it’s hard wired?

Most hard-wired smoke detectors include a 9-volt backup battery that’s supposed to kick in if your home loses electricity. If that battery is running low, your detector alerts you with a

high-pitched beep

. … Remove the old battery and replace it with a new one. Press the “test” button and listen for a beep.