How Can I Make My Harley Exhaust Louder?

by | Last updated on January 24, 2024

, , , ,


Remove the baffles or drill holes in them to increase air flow

through the pipes. By doing so, the motorcycle’s pipes will be very loud. However, while drilling out the baffles or drilling holes in them will make the Harley louder, it will not improve performance.

How do I make my Harley pipes louder?


Remove the baffles or drill holes in them to increase air flow

through the pipes. By doing so, the motorcycle’s pipes will be very loud. However, while drilling out the baffles or drilling holes in them will make the Harley louder, it will not improve performance.

How can I make my motorcycle exhaust louder?

  1. Install an Aftermarket Exhaust. Depending on what type of motorcycle you ride and what type of exhaust you install, you can change how your motorcycle sounds. …
  2. Tune or Change Your Stock Carb. …
  3. Buy the Best Aftermarket Ignition You can Get. …
  4. Shop Customized Exhaust Systems and Mufflers.

How can I make my Harley exhaust deeper?

  1. Replace or Modify the Stock Muffler. Stock mufflers suit a wide range of personalities and preferences. …
  2. Remove the Baffles. …
  3. Get a Full Performance Exhaust System. …
  4. Shop Slip-On Mufflers at West End Motorsports.

What makes a Harley loud?

Many Harleys are loud because the owners want them that way. … It is Harley owners who make several aftermarket modifications on their bikes to turn up the volume. Such changes include

removing bike mufflers

, replacing stock exhaust pipes with straighter aftermarket variants, or replacing the entire exhaust system.

Will removing baffles hurt my Harley?

If you remove the baffles or add a free flowing air filter it

will run even leaner

. You could add a fueler to richen up the air fuel ratio. The new Gen3 will be easy to install and adjustable for any future mods you might make.

Is it OK to take the baffles out of a Harley?

The baffles are located in the pipes of the exhaust system of your Harley and can be removed without damaging the bike. You

can take your bike to an authorized Harley Davidson shop

to have this done, but the cost will be much higher than doing it yourself using tools that you likely have on hand.

Is it bad to remove baffles on motorcycle?

Removing baffles on your motorcycle

will not directly harm or damage the engine

. However, it may result in the engine running leaner, causing a problem with its performance and complications to the emissions. Removing the baffle does not add any performance benefit or enhancements to the engine.

How do you make your exhaust louder without changing it?

  1. Replace the muffler with one designed to amplify the sound of your vehicle. …
  2. Add a sound-amplifying exhaust tip.

What makes an exhaust sound deep?

Start the engine, and walk around the vehicle while someone revs it up, so you can hear how it sounds. If you want it a bit deeper,

you can widen the cut to about a third of the pipe’s circumference

. Additional cuts, spaced about four inches apart, will add depth and volume to the sound.

Can I drill holes in my motorcycle muffler?

Drilling holes on motorcycle exhaust for sound is pretty easy. It’s all about drilling small holes with a

1⁄4 inch drill bit

at the end of the exhaust (the muffler). Drill one hole at a time because you can’t reverse a drilled hole!

How do I make my exhaust sound sporty?

  1. Step 1: Replace the Muffler. Factory installed mufflers are designed to absorb as much sound as possible. …
  2. Step 2: Add or Replace Exhaust Tip. An exhaust tip is an inexpensive addition that is plug and play. …
  3. Step 3: Have the Exhaust Tubing Evaluated. …
  4. Step 4: Consider a Turbocharger.

How loud is a Harley-Davidson in dB?

A Harley out of the factory is

80 decibels

. A Harley with straight pipes (no muffler) gives off 100 decibels, the same as a car horn at three feet according Purdue University. By comparison, an idling car emits 35-to-45 decibels and about 70 decibles at freeway speeds. But remember the decibel stem is logarithmic.

Are Harley engines noisy?

The Harley V-twin

engine is characteristically noisy

. Many owners find themselves fretting over engine sounds that clatter, tick, and rattle, but experience no ride-ability issues or loss of performance.

How loud is too loud for a motorcycle?

Final EPA regulations called for maximum levels of

83 dB for motorcycles manufactured in model year 1983

and 80 dB for motorcycles manufactured in model year 1986 or later. EPA heard testimony from motorcycle manufacturers and others on the optimum noise level for street motorcycles.

Rebecca Patel
Author
Rebecca Patel
Rebecca is a beauty and style expert with over 10 years of experience in the industry. She is a licensed esthetician and has worked with top brands in the beauty industry. Rebecca is passionate about helping people feel confident and beautiful in their own skin, and she uses her expertise to create informative and helpful content that educates readers on the latest trends and techniques in the beauty world.