Find it
in the lower corner of your windshield on the driver's side
. Your VIN number is your vehicle identification number and you can find your engine size by VIN number. In the series of numbers and letters, the tenth from the left denotes the model year and the eighth is the engine codes.
How can I get my check engine light codes without a Chevy scanner?
Making use of
the odometer is another way to retrieve the OBD2 codes. The user is required to depress the vehicle's odometer. (The “reset” and “trip” buttons must be reset as well.) Simultaneously, the ignition key of the vehicle must be turned on and off.
How can I check my engine code without a code reader?
Flip your
car's ignition on
and off a couple of times without cranking the engine and finish with the key in the on position. Your car will then check for any saved trouble codes. All the lights on the dash should light up until one remains on—usually the “service engine” light.
How do I reset my check engine light without a scanner?
The simplest most straightforward way to get rid of the check engine light is
to drive it for a little bit
, and the light will turn off by itself. Once you drove your car for a couple of days (e.g., usually three days), the check engine light should be gone.
Can AutoZone read codes without check engine light?
Does AutoZone Scan Check Engine Lights? AutoZone does. If your light is on, and you are wondering why, head down to your local AutoZone where one of our store associates can
help diagnose the issue through our free Fix Finder service
.
How do I turn my check engine light off?
The simplest most straightforward way to get rid of the check engine light is
to drive it for a little bit
, and the light will turn off by itself. Once you drove your car for a couple of days (e.g., usually three days), the check engine light should be gone.
How do I permanently delete engine codes?
A Permanent Diagnostic Trouble Code (DTC) is stored when a DTC is confirmed and the Malfunction Indicator Lamp (MIL) has been illuminated. A Permanent DTC can only then be cleared by the module strategy and cannot be erased by clearing DTCs with a scan tool, a
Keep-Alive Memory (KAM) reset
, or battery disconnect.
Will check engine light reset itself?
Your vehicle's check engine light
will will reset by itself once the issue or problem has been repaired
; this is true for most models. … A vehicle cycle is when you start your vehicle and drive it till it warms up, and then you turn the car off.
How far do you have to drive to reset the check engine light?
To make sure the check engine light does not reappear, it's recommended that you drive your car
30 to 100 miles
. This enables the vehicle's “Drive Cycle” to reset, as the various sensors need time to recalibrate.
Why is my engine light on but nothing seems wrong?
Normally, the appearance of a check engine light indicates a problem somewhere in your vehicle, but nothing seems amiss. Your car is still running at its best and there seems to be absolutely nothing wrong. … It doesn't have to take a
mechanical
issue in order for this light to appear.
Why is my car shaking and check engine light on?
The check engine light will come on when any of the following issues are detected by your vehicle's computer. Shaking or vibration may be caused by things such as
faulty spark plugs
, poor fuel pressure or misfires. … The other issue that may cause this type of shaking or vibration is a broken engine mount.
Can low oil cause the check engine light to come on?
Low oil pressure
: If your car is low on oil, it can cause your check engine light to go off. This is often shown in its own glowing light along with the check engine light on the dashboard. Overheating: If your car's engine temperature is heating up, it can once again trigger the check engine light.
How many miles do you have to drive to reset oxygen sensor?
Here's something you probably don't know: after clearing the car's computer you will need to drive for about
50 to 100 miles
. As you drive your car the computer will monitor all the sensors and register the results. You can use GOFAR to constantly monitor your car diagnostics.
Does disconnecting battery clear codes?
Leaving the battery disconnected for about 15 minutes will ensure the vehicle systems will completely reset when you reconnect the battery. …
Disconnecting the battery will clear the error codes
and reset the check engine light.
How long does it take for a car computer to reset?
The readiness monitors will remain until the car has been driven long enough for the computer to evaluate the various system and sensors. The amount of time can vary based on the vehicle. In some cases it can take
up to 100 miles
for all of the computer monitors to completely reset.
