How Do I Fix Code P1298?

1. Replacement of the Electric Load Detector.
2. Update or replacement of the PCM.
3. Repair open wires.
4. Repair or replace Open or shorted Electric Load Detector records.
5. Repair poor electrical connection in Electric Load Detector Circuit.

What is code P1298 for a Honda Civic?

Error Code P1298 is defined as

Electric Load Detector Circuit High Voltage

. This means the ELD (Electric Load Detector) is getting high input voltage.

What is eld on Honda Civic?

Honda's answer to this is the ELD (

Electrical Load Detector

). … This unit reads the amperage load directly from the battery and in-turn sends a varied voltage signal to the PCM which regulates the field signal to the alternator.

What is a Honda charging system?

For many years Honda and Acura have utilized a

dual mode charging system to increase fuel efficiency and to decrease the drag on the engine when starting

. … Thus, this system increases efficiency by charging the battery only when needed. Components. Honda/Acura charging systems appear to be similar to other manufacturers …

What is electrical load detector?

The Electronic Load Detector (ELD)

detects any electical load on the engine from accessories like A/C controls, radiator fan, lights

, heater motor, etc. The ECU uses the ELD's inputs to adjust alternator output and compensate for the additional electrical loads.

How do I fix code p1456?

What it means: OBD-II code P1456 represents a

problem with the EVAP control system on your Honda

. The EVAP control system on your Honda temporarily stores fuel vapors from the fuel tank in a canister to stop it from escaping into the atmosphere. … A faulty fuel cap could set off this engine code.

What is p1361 for Honda Civic?

The Honda Civic code p1361 means that the

crankshaft position sensor is not working correctly

. This is a part of the system that controls the timing of the pistons in the engine. If You do not fix this issue You will notice short term problems like shuddering, stalling, and rough idle.

How do I fix my P1166 code?

1. Repair short in the wire between A/F sensor relay and fuses.
2. Repair open in the wire between the PCM and the A/F sensor 1 or Secondary HO2S sensor 2.
3. Replace front O2 sensor.
4. Replace faulty PCM.

What causes charging system failure?

Another common problem that can cause the charging system to fail is

a broken alternator belt

or one that is worn so bad it slips badly. If the alternator works properly but the belt doesn't spin it fast enough, the voltage output can drop and cause the system to act as though the alternator doesn't work.

How do I check my charging system?

1. Remove the key from the ignition. …
2. Connect the red clamp to the positive terminal on your car battery.
3. Connect the black clamp to the negative terminal of your battery. …
4. Hit the MENU button, and you should see the Battery Test option. …
5. Select the battery voltage. …
6. Select Battery Location.

What does it mean when it says charging system failure?

What's happening when the battery/check charging system light comes on? Whenever this light goes on, it means that the vehicle is running solely on battery power. If the problem continues and your charging system fails,

the battery won't be able to recharge and it will soon run down, leaving you with a dead battery

.

What does code po442 mean?

What Does Code P0442 Mean? The

evaporative emission control

(EVAP) system prevents fuel vapors from escaping into the atmosphere. … If the EVAP system does not maintain the pressure, the ECM recognizes an evaporative emission control leak. In the case of P0442, it is a medium-sized leak, between . 020”-.

How do I turn my check engine light off?

The simplest most straightforward way to get rid of the check engine light is

to drive it for a little bit

, and the light will turn off by itself. Once you drove your car for a couple of days (e.g., usually three days), the check engine light should be gone.

Is it OK to drive with EVAP leak?

While it is safe to drive with an EVAP leak,

you should not drive your vehicle for long while you do have a leak

. If your Check Engine Light comes on, check to make sure the gas cap on your vehicle is securely fastened. If the light is still on, take it to a mechanic so the leak can be fixed.

What is TDC sensor in Honda Civic?

The TDC sensor

monitors a reference point on the camshaft that indicates where top dead center is on a cylinder

, usually cylinder number one. It sends a signal to the engine control module which, in turn, communicates to send a spark to the cylinder at top dead center.

What is a top dead center sensor?

The Top Dead Center Sensor (TDC)

detects when each piston is at top dead center

. This is used by the ECU to determine ignition and fuel timing at startup when the crankshaft position sensor is unable to determine accurate crankshaft speeds.