- Reset Spa Controller, power down and restart.
- Check for condensation under display glass.
- Check cable for crimps or any visible damage.
- Clean plug-in cable connections on both ends.
- Check power at Transformer on control circuit board.
- Check power at fuse on spa control circuit board.
How much does it cost to replace a hot tub control panel?
Cost to Replace a Spa Pack / Controls: Digital Spa Packs average $750.
Control systems average $450
. Cost to Replace Spa Jets: The cost to replace a spa jet varies from $20-$50 on average. Cost to Replace Spa Circuit Board: Hot tub PCBs range from $200-$600, with an average cost of $300.
How do I troubleshoot my hot tub control panel?
- Start by resetting the spa controller. …
- Check the controller for any condensation that may be present between the overlay and the display.
- Inspect the cables that run to the controller. …
- Check the circuit board transformer to make sure there is power.
How do you fix a circuit board on a hot tub?
When your hot tub or spa is not working like it should, the circuit board is one of the first things to check. If it turns out it is working fine, then
you can move on to other systems in your hot tub
. The first thing to do, just like with your old personal computer, is to turn off the spa and turn it back on.
How do I reset my hot tub control panel?
- Locate the spa’s high-limit reset. This is a red button found on many spa packs. …
- Press the high-limit reset button. …
- Turn on your spa and observe its operation. …
- Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
How do I know if my hot tub control panel is bad?
- Error messages or error codes may indicate the problem.
- Flickering display may indicate low voltage from transformer.
- Partial display may indicate dirty contacts or moisture.
- Blinking lights or flashing — indicates a system reset is needed.
How do I know if my control panel is bad in my hot tub?
- Error messages or error codes may indicate the problem.
- Flickering display may indicate low voltage from transformer.
- Partial display may indicate dirty contacts or moisture.
- Blinking lights or flashing — indicates a system reset is needed.
Can you replace hot tub control panel?
If you have a tub on your property, you may find
you need to replace or install
a hot tub control panel. These panels are the most commonly replaced parts, and while you can choose to call someone to repair it, you can also decide to do it yourself, at half the cost.
Is it worth repairing a hot tub?
If your hot tub is less than 10 years old, it’s probably worth fixing
. If the repair bill is half the cost of replacement, consider getting a new one.
Are hot tub control panels Universal?
The Universal Spa Control (USC) is a reliable spa control that
fits all hot tubs
and is a direct replacement for all spa brands. The USC spa pack is equipped with a 5500W (5.5kW), 4000W (4kW), or 3000W (3kW) spa heater. The USC control board can operate up to 4 water pumps.
How long should a hot tub circuit board last?
Being a spa’s central nervous system is no easy task, they’re exposed to all kinds of harsh conditions, so a circuit board’s normal life expectancy is usually
between eight and ten years
—yikes! Don’t fret, with proper care and attention your circuit board could last as long as twenty years.
Why is my hot tub control panel flashing?
It also provides a diagnostic function–a blinking power indicator indicates that
the heater high limit has tripped
, meaning that either the spa water is above its acceptable temperature range, or a malfunction has occurred within the spa (such as low circulation due to clogged filters).
Press the red reset button to reset the switch before reaching out to tech
support. Make sure the temperature probe is properly in the right amount of water to accurately read the temperature, and that there is no build up in the thermal well.
How do I test my spa control panel?
Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working
and connect it to the circuit board
.
How do I get rid of hot tub control panel?
- Step 1: Turn Off the Power. …
- Step 2: Break the Silicone Mounting Seal. …
- Step 3: Unplug Upper Control Connector. …
- Step 4: Remove Old Silicone. …
- Step 5: New Connector. …
- Step 6: Press New Panel. …
- Step 7: Turn On Power.
How do you reset a strong spa?
Press the RESET button on the GFCI
. The GFCI will reset and the spa will turn back on. The spa is now safe to use. If the GFCI trips while the spa is in use, press the RESET button.
