How Do I Unlock My Uniden Scanner?

Look for a “Lock” button among the buttons on the front of the device. Press and hold the button down until the key icon on the LCD display goes out

. The device is unlocked and ready for normal use.

How do I reset my Uniden Bearcat scanner?

1. Turn the scanner OFF and unplug the audio cable from the rear of the scanner.
2. Press and hold the L/O and PROG buttons.
3. While holding L/O and PROG, turn the scanner on.
4. Release the L/O and PROG buttons.
5. Press the PD/FD/EMG button THREE times.

How do you unlock scan mode on Uniden bc125at?

1. Press Hold to stop scanning.
2. Press and hold L/O until “Confirm Unlock All Channels?” appears in the display.
3. Press Pgm/E to unlock all or .Clr to cancel.

How do you unlock the Uniden bc75xll lockout?

The simplest way for this to occur is that you have just locked out all your programmed frequencies.

Just manually step to any channel in a bank that is toggled on and has programming in it, and toggle the LO key to reestablish at least one channel

to be unlocked.

What does lockout mean on a scanner?

Temporary Lock-Out Function

– lets you set your scanner to skip over specified channels or frequencies when scanning or searching. This temporary lock-out releases when you manually unlock the channels or frequencies or when you power down the scanner.

How do you unlock channels on Radio Shack scanner?

Press L/OUT to unlock a channel

. If there are no locked out channels, then the scanner will just beep. Note: You can still monitor locked out channels in manual and program modes.

How do I reset my Uniden ubc125xlt?

1. Turn the scanner OFF and unplug the audio cable from the rear of the scanner.
2. Press and hold the L/O and PROG buttons.
3. While holding L/O and PROG, turn the scanner on. …
4. Release the L/O and PROG buttons. …
5. Press the PD/FD/EMG button THREE times.
6. Press the AIR/MRN button THREE times.

How do I reset my scanner?

1. Click on ‘Start’ > ‘Settings’ > ‘System’ > ‘Intermec Settings’
2. Click on ‘Data Collection’ > ‘Internal Scanner’
3. Click on the Menu at the bottom of the screen.
4. Click on Restore Menu Defaults.
5. Click Yes.

How do I reset my Uniden BC345CRS scanner?

1. Remove backup batteries from the scanner.
2. Unplug the adapter from the back of the scanner, NOT from the wall.
3. Hold down the 2, 9, and HOLD keys.
4. Reconnect the adapter while holding the 2, 9, and HOLD keys.
5. Release the buttons once the screen indicates the memory has been cleared.

How do I reset my Uniden bct15x scanner?

Press and hold the Hold 2 and 9 buttons and turn the scanner back on

.

What is close call on a scanner?

Close call is an option on just about every available Uniden radio. It’s

a way to find frequencies that are close to you with a very strong signal

. Close call does not work over long distances or with weak signals. Close call won’t help you monitor local agencies while you’re traveling.

How do I find scanner frequencies?

One way to find frequencies is by

asking a retailer of police scanners

. Local directories also help you find the information you need, since the frequency depends on which county or state you live in. But by far, the quickest and most accurate route is through the internet.

How do I program my Uniden bc72xlt scanner?

1. Press HOLD.
2. Enter desired Channel (Not Frequency)
3. Press HOLD.
4. Press the FUNC key.
5. Press E.
6. Enter in the Frequency you want to program.
7. Press E to store the frequency in. Done!

How do you program a Radio Shack triple trunking scanner?

1. Press PROG, then press TRUNK.
2. Press FUNC, then use an UP or DOWN ARROW to select a bank.
3. Repeatedly press MODE to select a trunking mode (Motorola, EDACS,LTR).
4. Press PROG.
5. Enter the first control channel freq. …
6. Repeatedly press MODE to select a trunking mode (Motorola, EDACS, LTR).

How do I setup my Uniden scanner?

1. Press HOLD.
2. Enter desired Channel (Not Frequency)
3. Press HOLD.
4. Press the FUNC key.
5. Press E.
6. Enter in the Frequency you want to program.
7. Press E to store the frequency in. Done!

How do I program my Uniden bcd325p2 scanner?

1. Press HOLD.
2. Enter desired Channel (Not Frequency)
3. Press HOLD.
4. Press the FUNC key.
5. Press E.
6. Enter in the Frequency you want to program.
7. Press E to store the frequency in. Done!