- Locate the gas log control knob. …
- Light the gas logs by turning the control knob to the “pilot” setting. …
- Locate the switch at the front of the gas logs marked “on.” Move the switch to the “on” setting to ignite the burners below the gas logs.
How do you adjust the flame height on a gas fireplace?
Turn the key valve counterclockwise as far as it will turn to open the gas line. Start the fire by following your gas fireplace lighting instructions.
Turn the gas control knob to high
to increase the flames in your fireplace if applicable.
How do you adjust the airflow on a gas fireplace?
Insert a
flat-blade screwdriver into
the setscrew on the right side of the valve and twist counterclockwise to increase the gas-to-air ratio. Turn the setscrew clockwise to reduce air flow mixing with gas. Ask a friend to describe the flame color and intensity in your Heat-n-Glo fireplace to help with your adjustments.
Why is the flame on my gas fireplace so low?
Typically low flame height is caused by one of three things. Either you have
low gas pressure at the fireplace
or you need to restrict the venting to slow down the draft. 1) It is common to think that the gas pressure is fine when this only one appliance on the line or the meter is turned all the way up.
How do you adjust the flame on a gas log?
- Locate the gas log control knob. …
- Light the gas logs by turning the control knob to the “pilot” setting. …
- Locate the switch at the front of the gas logs marked “on.” Move the switch to the “on” setting to ignite the burners below the gas logs.
How do you purge the air from a gas fireplace?
While pressing the valve control knob in,
press the igniter button repeatedly until the pilot ignites
. This could take anywhere from one to 10 minutes to bleed air out of the lines as the gas starts to flow. Once the pilot is lit, continue to press the valve knob inward for 30 seconds before releasing it.
How do you adjust the regulator on a gas fireplace?
If the pressure readings aren’t ideal, you need to turn the regulator by 90 degree turns using your flat head screwdriver.
Turn it clockwise to increase pressure and counterclockwise to decrease pressure
.
What should the flame look like in a gas fireplace?
A healthy gas flame will burn steadily with
a yellow or orange
. If the flame is not yellow or orange it may be a sign that your gas fireplace needs adjusting or cleaning, which should be done by a qualified technician, such as those we have at Kozy Heat.
How high should the flames be on a gas fireplace?
Turn the burner on and set the flame height to high. Take a reading. This time, you want to see an ideal reading of
3.5 inches or the pressure rating
indicated in the manual. Don’t forget to turn off the burner and the gas and then tighten the screw again.
How do I control the heat on my gas fireplace?
- Locate the gas log control knob. …
- Light the gas logs by turning the control knob to the “pilot” setting. …
- Locate the switch at the front of the gas logs marked “on.” Move the switch to the “on” setting to ignite the burners below the gas logs.
How can I make my gas fireplace look better?
- Step 1 | Install the burner bed on andirons with a grate or in a fire basket. …
- Step 2 | Invest in beautiful ceramic logs. …
- Step 3 | Place a fireback against the back wall of the fireplace. …
- Step 4 | Place antique fireplace accessories around the fireplace.
How do I increase gas flow in my fireplace?
Turn the key valve counterclockwise as far as it will turn to open the gas line. Start the fire by following your gas fireplace lighting instructions.
Turn the gas control knob to high
to increase the flames in your fireplace if applicable.
Is there always a small flame in a gas fireplace?
The little flame you see in your gas fireplace after you have turned it off is called
a pilot light
. A Standing Pilot Light runs constantly, whether your fireplace is on or off. … What that means is that you don’t have a pilot light burning in your fireplace year around. When your fireplace is off, it’s all off.
How do you start a gas fireplace after the summer?
- Look over the user manual included with your fireplace. …
- Remove your fireplace’s outer cover. …
- Put a fireplace key into the device’s gas valve knob. …
- Hold a long lighter up to the burner and ignite it. …
- Turn the gas key. …
- Replace the fireplace’s outer cover immediately.
What does it mean to purge a gas line?
Purging is
the process of displacing gas/air within a pipeline or pipeline section with natural gas, air, or an inert gas
. o Purging a pipeline of air with gas is required: ▪ Whenever a pipeline or pipeline section is newly installed ▪ Whenever a pipeline or pipeline section has been removed from service and is being …
How do you clear a natural gas line?
Before doing anything, make sure that the gas supply is turned OFF. Smaller gas lines such as 3/8′′ or 1/2′′ flexible copper tubing or flexible stainless steel tubing can sometimes be cleared by
pushing a wire or a plastic probe through the piping
.
