How Do You Change A Belt On A John Deere LT155?

1. Tools Needed. Safety glasses. …
2. Remove Mower Deck. Follow the instructions in the owner's manual to detach and remove the mower deck from under the tractor. …
3. Clean the Underside. …
4. Park the Tractor. …
5. Parts Reference. …
6. Remove Tension Spring. …
7. Remove Belt from Transmission. …
8. Remove the Idler.

What size drive belt does a John Deere LT155 take?

John Deere

38-inch

Deck Mower Drive Belt Fits LT133 LT155.

What is a traction drive belt?

The drive belt engages

the traction drive system on the snow blower

. If the belt becomes too worn and breaks, your snow blower will stop dead in its tracks.

What size drive belt does a John Deere LT133 take?

M126536 Deck Drive Belt Replacement for John Deere LT133 Lawn Tractor – PC2606 – Compatible with

38 Inch

Mower Deck V-Belt.

What size belt does a John Deere LT160 take?

How does a traction drive work?

Traction drives work by

using normal force to generate usable rotational torque via multi viscosity traction fluids

. … This rolling motion of traction drives allows them to be very efficient and low noise producing compared to the mainstream current technology such as gear and belt systems.

What gear types are used in traction drives?

Traction drives, Figure 22, trans- mit mechanical power from source to load by means of mating metal rollers, which may be considered gears with infinite numbers of teeth. These rollers can be

cones, cylin- ders, discs, rings, spheres, or toroids

.

Why does the belt keep coming off my John Deere mower?

The drive belt may come off a riding mower

because it is damaged or loose

. … If broken or worn, the belt can break while the engine runs, and it can fly off at a great velocity, which is highly dangerous. Check the belt for looseness, cracks, fraying or separation from the rest of the assembly, and replace if necessary.

What size belt does a John Deere L110?

It is 42′′ and the L110 needs a

48′′

belt.

What is the difference between a deck belt and a drive belt?

So, with the mower deck removed from the tractor, the “drive belt” would be the one

still

on the tractor. The mower deck itself will still have the internal “deck belt” which if you turn one blade by hand, all blades turn because that deck belt is what connects and drives all the blades together.

How long should a mower drive belt last?

Good mower belts should last for

about 3- 4 years

. If you don't have a quality mower belt, you need to get one to use it for this long.

What size belt goes on a John Deere L130?

Mower Belt for L120 and L130 Models.

Do you have to remove mower deck to replace belt?

To replace this belt,

the deck should be off the lawn mower

. … To remove the front of the belt from the engine pulley, you may have to remove the cap screw from the center of the pulley and PTO to the engine crankshaft.

What year was the John Deere L130 made?

From what I see, it is a 23 hp engine, built around

2003-2005 era

.

How do you remove the pulley on a John Deere mower spindle?

Remove the large nut on top of one of the spindles. Turn on the air compressor and attach the

air wrench

to the compressor. Holding the spindle with one hand, place the air wrench on top of the nut, set the air wrench to the reverse setting and pull on the trigger. Once the nut is removed, slide the pulley off.

How do I turn the blades on my John Deere riding mower?

1. Turn the key to the “on” position, advance the throttle to half speed and allow the engine to warm up for 2 minutes. …
2. Lower the mower to the desired cutting height. …
3. Engage the mower blades; push the lever to the right of the steering wheel all the way forward.

Are John Deere decks interchangeable?

So, are lawn mower decks interchangeable?

Lawnmower decks are largely interchangeable

. Engines will swap without issue. However, blades and drive systems may differ.