How Do You Change Rear Brake Pads?

by | Last updated on January 24, 2024

, , , ,
  1. Remove the wheel.
  2. Remove the slider bolt.
  3. Pivot the caliper up.
  4. Slide out the old .
  5. Replace the retaining clips.
  6. Slide in the new brake pads.
  7. Retract the pistons.
  8. Monitor the brake fluid level.

How long does it take to change rear brake pads?

Usually, changing a set of brake pads takes

approximately 30 minutes to an hour

. If you have a professional complete the work, expect to pay for about an hour's worth of labor. It's worth pointing out that, as an amateur, it could take you upwards of 3 or 4 hours (maybe even longer) to replace your brake pads.

Can you replace your own brake pads?

If you're comfortable with doing your own car maintenance, you can take on replacing your own brake pads as a

DIY

project. As with all auto repairs or upgrades, consult your owner's manual for specific instructions or special information before you begin.

What happens if I change the brake pads but not the rotors?

Old rotors typically have unique wear patterns and brake dust from the old brake pad set. As a result, the new brake pads might not fit the old rotor perfectly. This mismatch

creates brake noise and vibration

and can cause uneven wear on the new brake pads (which will lead to premature brake pad replacement).

Is it harder to change rear brake pads?

Although changing brake pads seems simple in theory, it can quickly turn into a

complicated

project. There are a myriad of things that can go wrong with your brake job, which may require additional tools or parts that you don't have on hand. Modern cars are becoming increasingly complex.

How much does it cost to change your brake pads?

Typically, brake pad replacement costs about

$150 per axle

, or $300 total on average. That's just a ballpark estimate, though. Costs can range from between $100 to $300 per axle. Cheaper brake pads are made up of composite organic material.

Should car be in neutral when changing brakes?

You should have the

parking brake cable released at all times

when turning back the pistons. Once the new pads are installed and caliper is installed then pump the brakes using only short strokes. Do not push the pedal all the way down or master cylinder may be damaged.

Should you replace all 4 brake pads at once?

But, when changing brake pads, should you do all four at once? Well, first,

you absolutely should replace both front or both rear brake pads at the same time

. Unless something's really wrong, one should be wearing out at about the same rate as the other.

How much does it cost to change rear brake pads?

The average brake pad replacement costs

around $150 per axle

, but these costs can rise to around $300 per axle depending on your vehicle's brake pad materials. The least expensive brake pads use organic material.

How much should a full brake job cost?

A complete brake repair — one that includes pads, rotor and caliper replacement — typically averages

between $300 and $800

. However, depending on the make and model of your vehicle, you can easily spend more than $1,000 on a complete brake job.

Is it OK to put new brake pads on old rotors?

If new brake pads are put onto a vehicle with damaged rotors,

the pad won't properly contact the rotor surface

, reducing the vehicle's stopping ability. Deep grooves that have developed in a worn rotor will act as a hole-puncher or shredder and damage the pad material as it is pressed against the rotor.

Which brake pads wear out first front or rear?


Your front brake pads will

also wear down faster than your rear pads. The front of your vehicle handles a lot more weight transfer as you brake, causing more wear. Over time heat and friction also contribute to brake pad wear.

What are the signs of bad rotors?

  • VIBRATION. When rotors are warped or very worn, the contact between it and the brake pad can be imperfect. …
  • NOISE. Worn brakes are noisy and persistent squealing or squeaking is a sure sign of problems. …
  • VISIBLE DAMAGE. …
  • STOPPING DISTANCE. …
  • WILL I NEED TO GET THE ROTORS REPLACED?

How long does a brake job take?

How many hours does a brake job take? Generally, A Brake inspection takes

30 minutes to 1 hour

to replace the brakes including rotors and pads, & other vehicle components.

How much does Midas charge for a brake job?

Midas: Midas charges roughly

$80 per hour

for labor costs when working on brakes. They charge about $50 for a brake drum package, $60 to replace brake fluid, and upwards of $800 for a complete caliper and rotor job.

How many miles do brake pads last?

Average brake life runs

between 25,000 and 65,000 miles

, though some people will have brake pads last beyond 80,000 miles. While it's impossible to give an exact number, the 40,000-mile range is the general mileage to keep in mind when planning for vehicle maintenance.

Rebecca Patel
Author
Rebecca Patel
Rebecca is a beauty and style expert with over 10 years of experience in the industry. She is a licensed esthetician and has worked with top brands in the beauty industry. Rebecca is passionate about helping people feel confident and beautiful in their own skin, and she uses her expertise to create informative and helpful content that educates readers on the latest trends and techniques in the beauty world.