Press and hold the accelerator for 10 seconds or more
. Doing so erases the results of the self-diagnostic test, successfully clearing the forklift codes.
What does E32 mean on a forklift?
| Error Code Explanation | E30 ECCS C/U error signal | E31 Electronic control throttle control error signal | E32 Overhear signal (STEP 1) | E33 Overheat signal (STEP 2) |
|---|
How do you clear the fault code on a Toyota forklift?
- Press and hold buttons B and D simultaneously for 2 seconds. A short beep should sound both at the beginning of the 2 seconds and after 2 seconds has passed. …
- Press button C within 10 seconds. …
- Within 10 seconds, press and hold buttons B and D simultaneously for 2 seconds.
What does F 16 mean on a forklift?
f16 indicates
both directions are sending the same signal to the computer for over 2 seconds
..
How do you clear the code on a Hyster?
- Disconnect battery + connection.
- Replace display. See Electrical System 2200YRM1427 or Electrical System 2200YRM1327 .
- Restore battery connection.
- Turn truck power ON and press both the Scroll arrow buttons for two seconds.
What does SAS mean on a Toyota forklift?
To help prevent these inevitable situations, Toyota has equipped most of our forklifts since 1999 with the
patented System of Active Stability
(SAS.) SAS is an efficient and effective forklift system that takes over 3,000 readings per second to detect unsafe operating conditions.
How do I clear my Toyota OBD1 code?
- Turn off the vehicle's engine and open the hood.
- Disconnect the black-colored “Negative” battery terminal from the battery, using an appropriate size wrench.
- Leave the battery terminal disconnected for at least one minute.
How do you clear Komatsu Forklift error codes?
- Turn the forklift key switch on while simultaneously starting the stopwatch.
- Wait for 3 seconds, then proceed to press the forklift accelerator 5 times within 5 seconds.
Does Caterpillar make forklifts?
Cat lift trucks deliver innovative material handling solutions for your toughest applications. With load capacities ranging from 2,500 to 36,000 pounds, our forklift lineup consists of electric counterbalanced lift trucks to internal combustion (IC) cushion and pneumatic tire lift trucks.
What are the OBD1 codes?
| Code Description | Code 13 Oxygen sensor circuit open or no activity | Code 14 Engine coolant temp sensor error (high temp indicated) | Code 15 Engine coolant temp sensor error (low temp indicated) | Code 16 System voltage too low |
|---|
How do I check my OBD1 code with a paperclip?
Flip your car's ignition on
and off a couple of times without cranking the engine and finish with the key in the on position. Your car will then check for any saved trouble codes. All the lights on the dash should light up until one remains on—usually the “service engine” light.
How do you reset a car code without a scanner?
After removing the battery cables, you should proceed to cycle the ignition switch to the ON and OFF position for 3 to 5 times. Press on the
horn
button in the steering wheel. Keep it pressed for 30 seconds to a full minute to drain out all the stored power in the ECU capacitor. The horn is connected to a hot circuit.
What is a POS sensor on a forklift?
A typical forklift controls the traveling direction by operating the rear wheels. The angle position sensor or
multi-turn angle sensor installed on the rear wheels measures or detects the turning angle or direction of the rear wheels
.
What does A9 mean on a boiler?
An A9 error indicates that the
hot water temperature sensor is not sensing the expected outlet temperature
. The heater may continue to run in a “safe” mode with the A9 error code flashing or the error code may shut down the heater until the code is reset.
Who builds Caterpillar forklifts?
(MCFA) is a leading manufacturer of forklifts in the United States, Mexico, Canada and Latin America. Based in Houston, Texas, the company distributes three distinct brands – Mitsubishi forklift trucks, Cat® lift trucks and Jungheinrich® warehouse products.
