There is a way to do it.
You put a wrench on the pulley bolt and block the other end against the floor or the frame
. Then you use the starter motor to turn the engine (DO NOT START IT, JUST TURN IT) for at most one or two revolutions of the crank. Just enough to break the bolt loose.
How do you pull a pulley without a puller?
There is a way to do it.
You put a wrench on the pulley bolt and block the other end against the floor or the frame
. Then you use the starter motor to turn the engine (DO NOT START IT, JUST TURN IT) for at most one or two revolutions of the crank. Just enough to break the bolt loose.
How do you remove a stuck pulley from a shaft?
There is a way to do it. You
put a wrench on the pulley bolt
and block the other end against the floor or the frame. Then you use the starter motor to turn the engine (DO NOT START IT, JUST TURN IT) for at most one or two revolutions of the crank. Just enough to break the bolt loose.
How do you remove a crankshaft pulley?
- Position the puller in front of the pulley. …
- Install the puller-to-pulley bolts. …
- Using a breaker bar and socket, tighten the central puller bolt until the pulley slides off the crankshaft.
How do you remove a power steering pulley?
Using
an impact wrench or regular socket and ratchet
, remove the bolts that hold the power steering pump onto the bracket or the engine block. Usually there are two or three bolts that need to be removed.
How do you remove a pulley from a deck spindle?
Take bolt loose from top pulley
and remove the 4 bolts holding the Spindle with a socket. Screw the big nut back on the pulley, until nut is flush to the top ( if t doesn’t come off easy). Take a Rubber mallet and gently tap the top until it loosens the pulley.
How do I remove the MTD pulley?
Place a wrench onto the puller center screw and begin to tighten it slowly
. As the center screw tightens, it will pull the jaws towards it, and as the jaws get pulled, the pulley will come with them. This constant pressure as you tighten the screw will literally pull the MTD engine pulley straight off the shaft.
Which tool is used to remove the crankshaft pulley?
A half-inch drive impact gun
Why is my crankshaft pulley wobbling?
If the fan-belt pulleys that bolt to the harmonic balancer are dismounted, bent, or distorted
, it may cause the crankshaft pulley to wobble. … Sometimes, some dirt may get trapped under the pulley. Furthermore, the crankshaft pulley tends to wobble if it isn’t appropriately torqued.
How do I know if my crankshaft pulley is bad?
There are many reasons that a
belt
may start to wear and fail, and the most obvious is a failing crankshaft pulley. But this failing can work in reverse, in that a failing belt can indeed damage a crankshaft pulley. The rubber damping layer within a TVD can become worn as the belt itself becomes faulty.
What does a bad power steering pulley sound like?
A
whine
could mean a loose, damaged, or wet serpentine belt. Grinding or squeaking may indicate the power steering fluid is low, leaking, has air bubbles, or that the reservoir filter is dirty. A rattle could be a loose pulley or failing pump. The sound helps identify what to repair.
How do you tighten power steering pulley?
The
pump
may have failed or be leaking as well. If the pump was leaking onto the pulley, the buildup would cause the pulley to fail. … This component should keep the slack tight on the pulley. You will want to make sure the tensioner is working as well.
What holds the power steering pulley on?
A hydraulic power steering pump is driven by
a serpentine or drive belt
that is attached to the power steering pump pulley. As the pulley is driven by this belt and begins to spin, it turns an input shaft inside the pump which creates pressure inside of the pump’s housing.
How do you remove a pulley from a lawn mower that is stuck?
Spray a liberal amount of penetrating oil onto
the front and back sides of the pulley hub until they are thoroughly soaked. Spray the pulley retaining bolt and pulley shaft with the oil. Allow about 30 minutes to two hours for the penetrating oil to loosen the rusted pulley and other parts.
How do you remove a pulley from a mower deck?
- Remove the mower deck from the lawn tractor. …
- Remove the screws that hold the pulley guards over the pulleys and then place the pulley guard off to the side.
- Remove the bolt from the center of the pulley with a wrench.
How do you remove the spindle key?
Place the assembly over the key, and then thread the bolt into the shaft as far as it will go. Spin the nut downward against the block. Then
use a wrench to apply enough force on a nut
to remove the key from the shaft. If you apply enough downward movement, the key will be extracted.
