How Do You Replace A Hub Assembly?

1. Materials Needed.
2. Step 1: Prepare your work area. …
3. Step 2: Loosen the lug nuts. …
4. Step 3: Jack the vehicle up and use jack stands. …
5. Step 4: Remove the old wheel hub assembly. …
6. Step 5: Install the new wheel hub assembly and brake parts. …
7. Step 6: Reinstall the wheels.

How long does it take to replace a hub assembly?

Experience is one of the key factors affecting installation time. For new technicians, turnaround

time can be up to two hours

. However, that time can be cut in half by experienced technicians, especially if there are no delays in acquiring parts or tools.

How much does it cost to replace hub assembly?

The average cost for a Wheel Hub Assembly Replacement is

between $406 and $525

but can vary from car to car.

Do I need to replace the hub assembly or just the bearing?

Hub bearings are pre-packed at the manufacturer’s factory and are sold and installed as a complete unit. These cannot be taken apart for re-lubrication, but

must be replaced

.

How do you remove a hub assembly?

1. Raise vehicle and remove lug nuts and wheel.
2. Remove the brake caliper and rotor. …
3. Remove the axle nut, using an axle nut socket. …
4. Before removing hub unit, make a note of the proper orientation and positioning of the sensor wire and bearing. …
5. Remove the steering knuckle attachment bolts.

Is it safe to drive with a bad hub assembly?

Q: Is it safe to drive with a bad wheel bearing? A:

No. It can, in fact, be very dangerous to drive if one of your bearings is worn out

, especially since it may cause the wheel to stop while driving. Additionally, a damaged wheel bearing puts a lot of stress on the hub, the CV joint, and the transmission itself.

What happens when your hub assembly goes bad?

When the hub bearing assembly fails,

the driver is going to hear a noise

. It is described as a growling, rumbling or cyclical noise. The noise can increase or disappear when you increase your speed and may diminish when you turn in a specific direction.

How do I know if I need a new hub assembly?

1. Snapping, clicking or popping noises when cornering or making sharp turns.
2. Grinding noise when the vehicle is moving.
3. Knocking or clunking sensation from the vehicle.
4. Wheel vibration and/or wobble.
5. Poor steering control.

How long can you drive on a bad hub bearing?

In cases where you are in an isolated spot and your wheel bearing starts to go bad, you can possibly drive for

about 1600 kilometers

. Driving to this distance may not cause significant damage to your wheels.

What tools do you need to change a hub assembly?

1. Safety glasses.
2. Wheel chocks.
3. Jack and jack stands.
4. Ratchet, various size sockets and various size wrenches.
5. Breaker bar.
6. Mallet.
7. Punch.
8. Torque wrench.

Can I replace a wheel bearing myself?

Changing your own wheel bearings is considered an intermediate job that can be done at home, but will need some

speciality mechanic tools

. … Be sure to obtain your vehicle’s service manual and identify the type of wheel bearing your vehicle is equipped with before you begin the repair.

How do you get a wheel bearing out without pressing it?

1. Select the right surface.
2. Apply the vehicle’s parking brake.
3. Use a car jack to raise your vehicle.
4. Place jack stands under your vehicle.
5. Remove the coverings and trays that are in the way.
6. Remove the tires.

How expensive is it to replace a wheel bearing?

On average, a wheel bearing alone will cost you

between $60 – $150

, and an entire bearing and hub assembly replacement is around $200 – $400 for each wheel depending on your vehicle type.

What happens if you don’t fix wheel bearings?

Ultimate damage: If you don’t replace a damaged wheel bearing before it fails completely,

the wheel will completely seize up

. If this happens while you’re driving, the results can be catastrophic.

What causes a wheel bearing to fail?

The main reasons that a wheel bearing fails are: …

Impact damage or poor road quality

– all impacts from driving through a pothole, driving over speed bumps or hitting the curbstone can damage a wheel bearing and reduce its lifespan. Poor quality wheel bearing – a wheel bearing is continuously under enormous pressure.

How do you know your hub bearing is bad?

1. Humming Noise. The most easily identifiable and most common symptom of bad wheel bearings is an audible one. …
2. Squealing, Growling. …
3. Clicking Sound. …
4. Wheel Wobble. …
5. ABS Failure. …
6. Uneven Tire Wear. …
7. Vehicle Pulls to One Side. …
8. Steering Wheel Vibration.