How Do You Reset The Change Oil Light On A 2000 Pontiac Montana?

1. Turn ignition switch to ON position with engine off.
2. Fully depress and release the accelerator pedal 3 times within 5 seconds of turning key.
3. Change Oil lamp will flash for 2-10 seconds while it resets.
4. Once it stops flashing, the maintenance light reset is complete.

How do you reset the oil light on a Pontiac Montana?

1. With the ignition key in RUN, do not start the car.
2. After step one straight away press and release the accelerator pedal slowly three times within 5 seconds.
3. If the message for CHANGE OIL SOON light flashes 2 times, the system is reset.

How do you reset the change oil light on a 2002 Pontiac Montana?

1. Turn the ignition key to the “ON” position. …
2. Fully press and release the accelerator pedal to the floor slowly 3 times within five seconds. …
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

How do you reset the change oil light on a 2000?

To reset the 2000 Chevy silverado 1500 oil change light put the engine in the run position without starting the engine,

press the gas pedal to the floor 3 times within 5 seconds

, and then the change oil light will flash and then you can restart the vehicle.

Where is the reset button for oil change light?

1. Turn the car’s systems on, but leave the engine off. …
2. Locate the “Reset” button or stick, which is typically located on the dashboard, near the speedometer and fuel gauge.

How do you reset the change oil light on a 2004 Pontiac Montana?

1. Turn the ignition key to the “ON” position. …
2. Fully press and release the accelerator pedal to the floor slowly 3 times within five seconds. …
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

How do I reset my oil life?

Turn the

ignition back

to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.

How do I reset my engine oil level?

Locate the “reset” button or stick on the dashboard

. Normally this is found by the speedometer and tachometer behind the steering wheel. Hold the button down until the oil change light begins to flash. Turn the car off, wait a few seconds, then turn it back on.

How do you reset the change oil light on a 2001 GMC Sierra?

1. Turn the ignition to run (one position before starting engine).
2. Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
3. If the “Oil Life Reset” appears the system is resetting.
4. Turn the ignition off and then start the engine to verify the indicator has been reset to 100%.

Why is my change oil light still on?

If your oil light stays on even after changing your engine oil, you’re going to want to

check the sensor first to rule out a malfunctioning sensor as the cause

. … The oil pump may not be circulating enough oil to keep the engine’s parts lubricated and functioning properly, which can in turn cause multiple engine issues.

Why won’t my change oil light go off?

Check the oil. The light is a

warning signal that you are low on oil

or that the oil is not flowing properly. If the oil level is fine then the issue may be a reset button. Two different methods will allow you to reset the oil light.

How do you reset car warning lights?

1. Open the hood of your vehicle. …
2. Loosen the nut that holds the negative terminal to the battery with the pliers. …
3. Completely remove the cable from the negative battery terminal. …
4. Leave the battery disconnected for 10 minutes to ensure that the computer is fully reset.

How do you reset percentage after oil change?

1. Press the setup button and then release it.
2. You should now see a message that reads “Oil life % hold reset = new.”
3. Press the reset button and hold it down for about two seconds.
4. Let off the button and the “Oil Life [percentage (%)]” should reset to 100%.

How do you turn off the change oil light on a Jeep?

1. Put your Jeep in “Park” and turn off the engine.
2. Turn the ignition to the “On” notch, without starting the engine.
3. Push the gas pedal to the floor three times (within ten seconds). Turn the ignition to “Off,” and then start the engine to verify that the alert is turned off.

How many miles will 5 oil life last?

Hi There, Your oil life percentage is generally an estimated time designed to prompt the operator of the vehicle to have the oil changed as soon as possible. 5% is generally not something to be concerned about, but you should consider having the oil changed in the next

1,000 miles or less

.

How long does it take for oil light to go off?

Though most manufacturers have discovered this function helps to improve engine oil life, some has made this function obsolete. Typically, when you start off your engine, the oil service oil should come on for

about two seconds

then it stops. If this light stays on, it will mean your vehicle needs oil or filter change.