How Do You Reset The Change Oil Light On A 2009 Dodge Grand Caravan?

1. 1-Turn the ignition to run (second position)
2. 2-Press slowly the accelerator pedal all the way down three times within 10 sec.
3. 3-Turn ignition OFF.
4. 4-Then turn the ignition to RUN or start the engine to verify if the oil life has been reset.
5. 1 Person Made This Project!

How do you reset the change oil light on a Dodge Grand Caravan?

1. Turn the key to ON/RUN position with engine off.
2. Fully depress and release the accelerator pedal 3 times within 10 seconds.
3. Turn the key to the OFF position and then back on to confirm reset was accepted.

How do you reset the change oil light on a 2008 Dodge Grand Caravan?

1. 1-Turn the ignition to run (second position)
2. 2-Press slowly the accelerator pedal all the way down three times within 10 sec.
3. 3-Turn ignition OFF.
4. 4-Then turn the ignition to RUN or start the engine to verify if the oil life has been reset.

How do you reset the change oil light on a 2010 Dodge Grand Caravan?

1. 1-Turn the ignition to run (second position)
2. 2-Press slowly the accelerator pedal all the way down three times within 10 sec.
3. 3-Turn ignition OFF.
4. 4-Then turn the ignition to RUN or start the engine to verify if the oil life has been reset.

How do you reset the change oil light on a 2007 Dodge Caravan?

1. Stop the vehicle and turn the ignition switch to the RUN position without starting the engine. …
2. Fully depress the GAS PEDAL slowly three times within 10 seconds. …
3. Turn the ignition off and start the engine to verify the indicator has been reset.

How do I reset the oil change?

Turn the

ignition back

to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.

How do you reset the check engine light?

The simplest most straightforward way to get rid of the check engine light is

to drive it for a little bit

, and the light will turn off by itself. Once you drove your car for a couple of days (e.g., usually three days), the check engine light should be gone.

How do you reset the change oil light on a 2012 Dodge Caravan?

To reset the oil light to the 2010 dodge grand caravan, you will

turn the ignition to the on / run mode

. Move the gas pedal slowly three times in 10 seconds. Change the ignition switch to the lock button. Repeat this process if the indicator appears again after the engine is started.

How do you reset the computer on a Dodge Grand Caravan?

Disconnect the battery for 1 minute and re-connect.

start the vehicle and hold the revs at 1800-2000rpm for 10 seconds let the revs lower on their own then turn the a/c on and repeat

. this will reset the base idle of the engine.

How do you reset the change oil light on a 2005 Dodge Caravan?

1. Stop the vehicle and turn the ignition switch to the RUN position without starting the engine. …
2. Fully depress the GAS PEDAL slowly three times within 10 seconds. …
3. Turn the ignition off and start the engine to verify the indicator has been reset.

How do I reset dashboard after oil change?

Insert the key into the ignition and turn it to the “on” position without starting the engine. Press the the

gas pedal slowly to the floor three successive times within 10 seconds

. Turning the ignition off. If the light is still on the next time you start the truck, repeat the process.

Why is my change oil light still on?

If your oil light stays on even after changing your engine oil, you’re going to want to

check the sensor first to rule out a malfunctioning sensor as the cause

. … The oil pump may not be circulating enough oil to keep the engine’s parts lubricated and functioning properly, which can in turn cause multiple engine issues.

How do you reset the maintenance required light on a oil change?

1. Turn Your Vehicle on. Your key should be switched to the on position and look on your dashboard. …
2. Turn the Vehicle Off and Press the Trip Meter Reset Button. …
3. Turn the Vehicle Back on. …
4. Keep the Reset Button Pressed. …
5. Release the Reset Button.

How do I reset my check engine light without a scanner?

The simplest most straightforward way to get rid of the check engine light is

to drive it for a little bit

, and the light will turn off by itself. Once you drove your car for a couple of days (e.g., usually three days), the check engine light should be gone.

Will check engine light reset itself?

Your vehicle’s check engine light

will will reset by itself once the issue or problem has been repaired

; this is true for most models. … A vehicle cycle is when you start your vehicle and drive it till it warms up, and then you turn the car off.