To remove the code,
press pause or cancel button twice and the power button once
. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by
unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again
. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do I reset my Whirlpool Duet washer?
Unplug the washer for 30 seconds
to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
How do you reset a front load washer?
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you reset the control lock on a Duet washer?
- Locate the “Control Lock/Unlock” button on your Duet's control panel.
- Press and hold the “Control Lock/Unlock” button for three seconds.
- Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds.
When you turn it back on it should be reset
.
How do I run a diagnostic on my Whirlpool washer?
Whirlpool Duet Diagnostic Test Mode
Close
the washer door
. Select any one key except “Stop/Cancel” and Control Lock. If you got it right all the lights on the Duet washer's control should light up, and any error codes in the washer's memory will be displayed.
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer
and then plugging it back in often serves as the means to reset it
.
How do I reset my defy front-load washer?
First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a
Master Reset
. This will reset all of the onboard componentry and is often successfully used by appliance technicians.
Why did my front-load washer stop spinning?
Front-load washer tubs spin thanks
to a drive belt that runs off of the motor
. A loose, frayed, or torn belt could be why your washer won't spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
How do I fix the Control Lock on my Whirlpool Duet washer?
- Locate the “Control Lock/Unlock” button on your Duet's control panel.
- Press and hold the “Control Lock/Unlock” button for three seconds.
- Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.
How do I turn off the Control Lock on my Whirlpool front load washer?
To turn off Control Lock, press and hold the Options key that says
“Control Lock Hold 3 Sec” under it for 3 seconds
.
What do I do if my Whirlpool washer is locked?
Unplug your Whirlpool washer and leave it unplugged for 45 minutes. After 45 minutes,
plug your
washer back in. The washer's programming should be reset and the door should open.
How do I fix a Whirlpool washer error?
Unplug
the washer or disconnect the power for one minute and reconnect it again. Reselect the cycle and press Start. If the code persists, Contact Us or Schedule Service Online so a qualified technician can diagnose the washer.
Why is my Whirlpool washing machine not turning on?
One reason your appliance may not start is that it
has simply come unplugged
or that the outlet that it is plugged into has tripped your home's main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why did my Whirlpool washer stop working?
Some of the most common faults that will make your washer stop mid cycle include
thermostat failure
, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
