To reset the oil change indicator on the 2009 ford escape first turn the key to the on position, right before fully starting. Then you press the setup button until oil life x*x% hold reset = new” shows . Next you press and hold the reset button for a couple of seconds then release this should reset it.
How do you reset the oil change light on a Ford Escape?
Using the information display controls on the steering wheel, scroll to ‘Settings’ and press the right arrow button. Scroll to ‘Vehicle’ and press the right arrow button. Scroll to ‘Oil Life ‘ and press the right arrow button. Press and hold the OK button until a ‘Reset Successful’ message appears.
How do you reset the oil change light on a 2008 Ford Escape?
- Turn the ignition to run (one position before starting engine).
- Press the SETUP button until the “OIL LIFE XXX% HOLD RESET = NEW” displays.
- Press and hold the RESET button for two seconds and release to reset the oil life to 100% and “OIL LIFE SET TO 100%” is displayed.
How do you reset the oil change light on a 2010 Ford Escape?
Using the information display controls on the steering wheel, scroll to ‘Settings’ and press the right arrow button. Scroll to ‘Vehicle’ and press the right arrow button. Scroll to ‘Oil Life’ and press the right arrow button. Press and hold the OK button until a ‘Reset Successful’ message appears.
- Turn the car’s systems on, but leave the engine off. ...
- Locate the “Reset” button or stick, which is typically located on the dashboard, near the speedometer and fuel gauge.
Why is my oil change light still on?
If your oil light stays on even after changing your engine oil, you’re going to want to check the sensor first to rule out a malfunctioning sensor as the cause . ... The oil pump may not be circulating enough oil to keep the engine’s parts lubricated and functioning properly, which can in turn cause multiple engine issues.
What does a wrench light mean on Ford Escape?
The wrench warning light on Ford vehicles is the powertrain malfunction indicator light . When it illuminates, it means that the computer has detected an issue with your vehicle’s powertrain or four-wheel-drive system.
How do I reset my dashboard after oil change?
Insert the key into the ignition and turn it to the “on” position without starting the engine. Depress the gas pedal slowly three successive times within 10 seconds . At this point, the system should have reset. You can verify by turning the ignition off and then on again.
How do you reset the oil change light on a 2010 Ford Explorer?
- Press and hold the SELECT/RESET stem for more than two seconds. Oil life is set to 100% and OIL LIFE SET TO 100% is displayed. ...
- Once OIL LIFE SET TO 100% is displayed, release, press and hold the. ...
- After setting the oil life start value, press the SELECT/RESET stem.
How do I reset my warning light?
- Open the hood of your vehicle. ...
- Loosen the nut that holds the negative terminal to the battery with the pliers. ...
- Completely remove the cable from the negative battery terminal. ...
- Leave the battery disconnected for 10 minutes to ensure that the computer is fully reset.
How many miles will 5 oil life last?
Hi There, Your oil life percentage is generally an estimated time designed to prompt the operator of the vehicle to have the oil changed as soon as possible. 5% is generally not something to be concerned about, but you should consider having the oil changed in the next 1,000 miles or less .
How do I reset my service light?
Start with the ignition turned ON (position 2), but with the engine OFF. Pull out and hold the button on the right side of the display until “SERVICE” appears on the display. Release the button on the right, then within 5 seconds pull the button out and hold it again.
How long can I go after oil change light comes on?
On vehicles with an oil change light, an oil change is needed when the light remains on after startup. It’s best to schedule the oil change within one to two weeks . If you primarily do highway driving, you have a little more breathing room than city driving.
What are signs of oil pump going out?
- Low Oil Pressure.
- Increased Engine Temperature.
- Hydraulic Lifter Noise.
- Noise from the Valve-Train System.
- Noise at the Oil Pump.
- Stop Driving.
- Check the Oil Pressure Measurement Unit on the Engine.
- Check the Engine Oil Port Pressure Using A Gauge.
How long can you drive with oil light?
Then there are problems with starting the engine. Which means only one thing – oil starvation will begin very soon (if it has not already begun). This is very harmful to the powertrain. In this case, you can drive about 200 km , after which you need to add lubricant.
