On the steering wheel, navigate to the “Oil Life” selection under “Vehicle Info“. Push and hold the OK button until the
oil light percentage changes to 100%
. Press the Start/Stop button to turn the electronics off.
How do you reset the oil light on a 2015 Jeep SRT?
- Turn the ignition switch to the ON position, do not start the engine.
- Fully depress the accelerator pedal slowly three times within 10 seconds.
- Turn the ignition switch to the OFF/LOCK position.
How do you reset the oil change light on a Jeep Cherokee?
Without holding the brake pedal, press the Start/Stop button to turn on the electronics. Do not start the engine. On the steering wheel, navigate to the “Oil Life” selection under “Vehicle Info“.
Push and hold the OK button until the oil light percentage changes to
100%.
How do you reset the oil life on a jeep?
Without starting the engine, turn the ignition in the ON/RUN mode position. In the instrument cluster display, navigate
to “Vehicle Info”
then “Oil Life.” Push and hold the ‘OK’ button until the oil life gauge resets to 100%.
How do you turn off the change oil light on a Jeep?
- Put your Jeep in “Park” and turn off the engine.
- Turn the ignition to the “On” notch, without starting the engine.
- Push the gas pedal to the floor three times (within ten seconds). Turn the ignition to “Off,” and then start the engine to verify that the alert is turned off.
Why is my oil change light still on?
If your oil light stays on even after changing your engine oil, you’re going to want to
check the sensor first to rule out a malfunctioning sensor as the cause
. … The oil pump may not be circulating enough oil to keep the engine’s parts lubricated and functioning properly, which can in turn cause multiple engine issues.
How do I reset my oil life?
Turn the
ignition back
to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.
Why is my change oil light on when I just changed my oil?
The light could be on after an oil change
because of an issue with the oil pump
. If this is the cause, there could be not enough oil circulating through to the various parts. Performing regular oil changes should help prevent this from happening, but parts do wear out.
Why is my Jeep engine light on?
If the check engine light in your Jeep Wrangler starts flashing, that means that the problem needs immediate attention and your
Jeep should be brought in hastily
. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system.
Will my jeep tell me when I need an oil change?
The indicator system will light up when an oil change is needed
. Typical operating conditions means the car can last up to about 10,000 miles before needing the oil changed, but that may need to be adjusted depending on how the car is driven.
How do you reset the engine light on a Jeep Wrangler?
- Make sure the engine is not running and key is out of the ignition.
- Disconnect the battery terminals.
- Wait 5 minutes.
- Reconnect battery terminals.
- Insert and turn the ignition key to the run position without starting.
- All error codes are cleared and CHECK ENGINE icon disappeared.
Do you have to reset oil light after oil change?
Do not reset the oil light unless you have actually changed the oil
. The light is there to tell you when it’s time to change the oil. Resetting the light without changing the oil may cause you to miss an oil change, which can damage your engine.
How long can I go after oil change light comes on?
On vehicles with an oil change light, an oil change is needed when the light remains on after startup. It’s best to schedule the oil change
within one to two weeks
. If you primarily do highway driving, you have a little more breathing room than city driving.
How long can you drive with oil light?
Then there are problems with starting the engine. Which means only one thing – oil starvation will begin very soon (if it has not already begun). This is very harmful to the powertrain. In this case, you can drive
about 200 km
, after which you need to add lubricant.
How do you reset percentage after oil change?
- Press the setup button and then release it.
- You should now see a message that reads “Oil life % hold reset = new.”
- Press the reset button and hold it down for about two seconds.
- Let off the button and the “Oil Life [percentage (%)]” should reset to 100%.
How many miles will 5 oil life last?
Hi There, Your oil life percentage is generally an estimated time designed to prompt the operator of the vehicle to have the oil changed as soon as possible. 5% is generally not something to be concerned about, but you should consider having the oil changed in the next
1,000 miles or less
.
