Very easy to fix,
put the key in the drivers door, turn it to lock and unlock about 3-5 times
, that will reset it.
How do I get my Jeep Cherokee out of security mode?
Press the power door-lock switch on the keyless entry fob
. Close the driver’s side door. Leave all doors closed for about 16 seconds until the Vehicle Security Light on the instrument cluster stops flashing quickly. When the light flashes at a slower rate, this signifies that the system has been reset and rearmed.
How do I get my car out of anti theft mode?
Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car. Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.
How do I reset my Jeep Cherokee?
- Disconnect the battery by removing the positive battery cable.
- Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
- Reconnect the positive cable to the battery.
- Turn the key to on but do not start.
- Turn the headlights on.
Where is the anti theft code on a Jeep Cherokee?
You can find this serial number on the anti-theft identification card usually
placed in the glove box
at the time of purchase. You can also find the serial number of the radio on the screen of your Jeep radio itself.
How do I get my car out of anti-theft mode without remote?
- Close all of your car doors.
- Insert one key in the door lock and cycle it to the “Lock” position, and then back to the “Unlock” position two times. …
- Enter your car and insert your key into the ignition cylinder.
- Cycle the key in the ignition from the “Off” position to the “On” position twice in a row.
Is my car in anti-theft mode?
If the security or anti-theft light is flashing when you attempt to start your car, and the engine does not crank or does not start, you have an
anti-theft problem
. The system may not be recognizing your key or keyless entry signal, or there may be a fault in the anti-theft module, keyless entry system or wiring.
What would cause a Jeep Cherokee to not start?
The most common causes that hinders normal starting operation of your Grand Cherokee are
dead key fob battery
, dead 12v battery, corrosion on battery terminals, bad alternator, clogged fuel filter, broken starter, blown fuse, empty gas tank, immobilizer error or any fault in the electrical system.
How do you reset the MIL light on a Jeep?
- Make sure the engine is not running and key is out of the ignition.
- Disconnect the battery terminals.
- Wait 5 minutes.
- Reconnect battery terminals.
- Insert and turn the ignition key to the run position without starting.
- All error codes are cleared and CHECK ENGINE icon disappeared.
How do I reset my jeep battery?
- Jeep Electronic Control Unit Reset. …
- Disconnect the battery by removing the positive battery cable. …
- Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
- Reconnect the positive cable to the battery.
- Turn the key to on but do not start.
- Turn the headlights on.
How do I reset the anti theft on my Jeep Cherokee?
Press the power door-lock switch on the keyless entry fob
. Close the driver’s side door. Leave all doors closed for about 16 seconds until the Vehicle Security Light on the instrument cluster stops flashing quickly. When the light flashes at a slower rate, this signifies that the system has been reset and rearmed.
How do I find the security CODE on my jeep radio?
The best place to locate a radio code is
in the owner’s manual of your car
. In most cases, the owner’s manual will be located in your glove box and will include general automotive service and maintenance tips, along with instructions on how to operate each system on the vehicle.
How do I reset my car radio without the CODE?
Turn on your radio and see if it displays CODE or LOC. If it does, turn off the radio.
Press and hold down the audio power button together with the SEEK button for about 50-60 minutes
. Then, it will turn on without entering the radio code.
Why is my car in anti theft mode?
The anti-theft system of your car
may not work properly at a certain time
. This may be for many reasons, including a dead car battery that loses memory of your key or a dead remote control battery. It may also be that the immobilizer chip is damaged on your key or the car door lock is damaged.
Will disconnecting battery reset anti theft?
By
unplugging the battery for a few minutes
, it will also reset the computer. … All you have to do is disconnect the positive or negative terminal and wait.
How do you reset anti theft?
Leave the key in position for about 10 – 15 minutes. Step 3: Check the anti-theft light again.
If it’s no longer blinking, turn the key back to the Off position and allow it to set for a minute or two
. This gives the system time to reset or you won’t be able to start your car.
