How Do You Set The Clock On A 2006 Jeep Liberty?

1. Press and hold the TIME button until the hours blink.
2. Adjust the hours by turning the right side TUNE/ SCROLL control knob.
3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes.

How do you set the clock in a Jeep Liberty?

1. Locate the clock-setting buttons on the left side of the audio systems panel in your Jeep Liberty. …
2. Hold down the “H” button to set the clock’s hours digits to the appropriate time.

How do you change the time in a 2005 Jeep Liberty?

1. Hold down the “Time” button, located at the top of the audio systems panel, until the hours digits on the digital display begin to blink.
2. Turn the “Tune/Audio” control, located on the right side of the audio panel, until the hours place digits reflect the desired number value.

How do I reset my 2006 Jeep Liberty?

1. Turn on the engine.
2. On the vehicle’s dash, press the “Step” button until “Miles to Service” is displayed.
3. Press and hold the “Reset” button, near the “Step” button, until the “Miles to Service” flashes and resets. Verify the “Perform Service” light goes away.

How do I reset the clock on my Jeep?

To help set the clock, first, you must

locate and press the ‘Time’ button

, which can be found on the outside of the Uconnect unit. After holding down the ‘Time’ button for a few seconds, you’ll notice the time display starts to flash. This is a good sign as it indicates that the clock is ready to be set.

How do you set the clock on a 2008 Jeep Liberty?

1. Press and hold the TIME button until the hours blink.
2. Adjust the hours by turning the right side TUNE/ SCROLL control knob.
3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. …
4. Adjust the minutes using the right side TUNE/ SCROLL control knob.

How do you clear the codes on a Jeep Liberty?

1. Open the driver’s side door of the Jeep Liberty and locate the diagnostic link connector (DLC) under the dash.
2. Plug the pocket scanner into the DLC and then turn the ignition key to the accessory position.
3. Read the onscreen menu of the scanner.
4. Choose “Erase” as an option.

How do I reset my 2008 Jeep Liberty?

1. Turn the ignition to run (one position before starting engine).
2. Fully depress the accelerator pedal slowly three times within 10 seconds.
3. Turn the ignition off and then start the engine to verify the indicator has been reset. Categories. Automotive (448) Archives.

What does perform service mean on a 2006 Jeep Commander?

when it says “perform service”,

you press and hold the reset button until it resets

. In the menu options, set it for the interval you want to be reminded to get an oil change.

How do you set the clock on a 2006 Jeep Wrangler?

Set the Clock

Press the

“Time” button

on your Uconnect unit and hold it until the hours digits flash. Turn the tuning knob clockwise or counterclockwise to increase or decrease the hour value. Once the hour is correct, press and release the tuning knob and the minutes digits will flash.

How do you set the clock on a 2017 Jeep Grand Cherokee?

Press the menu button to the right of the console screen. On the

screen, touch System setup, then Time setup

. Touch the up and down buttons to reach your desired hour and minute.

How do you set the clock on a 2002 Jeep Liberty?

Insert the tip of a ballpoint pen into the hole labeled with an “H” for the

hour setting. There is a small button inside the hole. Press the pen in and let off repeatedly while watching the hour on the clock advance. Stop when you get to the correct hour.

How do you set the clock on a 2007 Dodge Ram?

Push the

SETTINGS button

on the right side of the radio faceplate. If the settings button is not present, push the MORE button on the faceplate then the “Settings button” button on the touch- screen. 2. Select the “Clock and Date” button on the touchscreen.

How do you set the clock on a 2008 Jeep Wrangler?

Set the Clock

Press the

“Time” button

on your Uconnect unit and hold it until the hours digits flash. Turn the tuning knob clockwise or counterclockwise to increase or decrease the hour value. Once the hour is correct, press and release the tuning knob and the minutes digits will flash.