Keep the forks
6 to 10 inches above the
ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
How low should forks be driving forklift?
Keep the forks
6 to 10 inches above the ground
to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
When leaving a forklift parked the forks should be?
Lower the forks to the floor when parking the forklift. Make sure
that the forks touch the ground when you
are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.
When parking a lift truck the forks should be raised off the ground?
A properly trained operator will carry his forks or load
4-6 inches off the ground
. This position is high enough to reduce contact with dock plates, expansion joints in concrete, uneven areas, slight slopes, inclines and debris on operating surfaces.
When traveling with a load the lift forks should be how far off the floor?
Lower the load so that its lowest point is
15 to 20 cm (6 to 8 inches)
from the floor. While traveling, keep the load at a safe travel height.
Where should you not park forklift?
Do not park the forklift in
a location with its fork arms protruding the passageway
, where there are a lot of pedestrians who will have to step over them. Do not leave the truck in any access doorways and it should not block any stairways of the workplace. Never leave the truck near first aid stations.
Is it illegal to leave keys in a forklift?
In fact, leaving keys in an unattended forklift (or, thus, leaving on the ignition of this vehicle)
is illegal
, and has dire consequences as a safety hazard, even without the actual occurrence of an accident. Know and never exceed the lifting capacity of the forklift.
What should you do every time you park a forklift?
- Always try to find a level surface to park on. …
- Lower forks, or the forklift attachment, all the way to the ground. …
- Put the gear into neutral.
- Make sure the wheels are straight. …
- Set the parking brake every time you park the forklift. …
- Turn off the engine before dismounting the forklift.
When driving with an empty forklift forks should be kept 18 to 24 inches off the ground?
When driving a empty forklift,forks should be kept 18 to 24 inches off the ground. The safest way to cross curbs and railroad tracks is at an angle. When working with pallets ,forks should be positioned as widely apart a possible.
When a lift truck is turning Is it more stable loaded or unloaded?
An unloaded forklift’s center of gravity is between the axle of the steer wheels at A and the drive wheels at B-C. When the forklift is unloaded, the location of the center of gravity is the only factor for determining stability. … When a forklift is loaded properly,
it becomes more stable
.
When traveling with a load your forks should be no more than 6 inches off the floor?
Keep the forks
6 to 10 inches above the ground
to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
What will make the load more stable during travel?
When traveling with a load, always make sure
to tilt the mast of the forklift backward
so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.
How should you normally drive a forklift?
- Always drive unloaded forklifts with the forks downgrade.
- Never drive a loaded forklift with the load downgrade.
- When driving up a ramp, drive loaded forklifts forward with the load upgrade.
What 3 guards are fitted to a forklift?
The forklift overhead guard protects an operator from falling loads. Overhead guards for forklifts categorized as
Class I, II, IV and V
must meet the Falling Object Protection (FOP) requirement.
What is the largest cause of fatal or serious forklift accidents?
Forklift overturns
are the leading cause of fatalities involving lift trucks. Overturns can be caused by: Improper turning. Driving with an elevated load.
What should you always do before reversing the forklift?
- Keep a clear view in the direction of travel.
- Look in the direction of travel. …
- Always be aware of limited visibility, and use extra caution when driving in reverse.
- Consider using ground guides, rear-view mirrors, spotters, or other aids to increase visibility while operating in reverse.
