That’s very difficult to answer due to the multiple variables involved in removing and replacing hard to access components such as the center driveshaft on a front wheel drive vehicle like your Edge. However, in general, this type of job can often be completed
in one business day
; or less than 8 service hours.
Is it hard to disconnect a drive shaft?
Make sure you place a
basin under the driveshaft to transmission joint
. To totally disengage the driveshaft, you need to use both hands and slide the driveshaft gently away from the transmission case or transmission. You will notice some fluid leaks out, that’s why you placed the basin.
How easy is it to change a driveshaft?
Changing your driveshafts is actually a
simple task
that a home mechanic can undertake without too much trepidation. It’s just a case of being thorough, being safe, and of course, having your trusty Haynes Manual to hand.
How do you remove a drive shaft?
That’s very difficult to answer due to the multiple variables involved in removing and replacing hard to access components such as the center driveshaft on a front wheel drive vehicle like your Edge. However, in general, this type of job can often be completed
in one business day
; or less than 8 service hours.
How much does it cost to replace the drive shaft?
You can usually expect to pay
between $320 and $750
for the average cost of the parts, while the cost of the labor is between $150 and $190. If you have a rear wheel or four wheel drive car, then the price of the broken drive shaft repair cost will be much higher.
What happens if you don’t mark your driveshaft?
If they split the shaft and not re install it correctly,
they will throw the shaft out of balance and cause an uncomfortable vibration
. One piece shaft guys have the slip yoke in the t-case, so they dont have to worry about any of this.
Can you remove the rear drive shaft and still drive?
Yes
, you can if you remove the rear driveshaft. Basically you’d be in front wheel drive mode. Assuming you mean the u-bolt on the rear of the driveshaft It’s not going to hurt anything.
Should you turn a drive shaft by hand?
So, yes,
you should be able to rotate the driveshaft by turning the wheel
. However, with that said, I personally would get under the car and rotate the DS by hand to visually examine the DS and center mount, Joints, etc. There will be a front and rear Ujoint for each half of the driveshaft with a center bushing.
What noise does a bad drive shaft make?
Generally speaking, a bad drive shaft is going to create a kind of
rattling or clunking sound
. You may also hear sounds that are like a high-pitched squeaking or a scraping noise of metal on metal. All of this will originate from underneath your car, rather than in the engine compartment.
What are the signs of a bad drive shaft?
- Vibrations from under the vehicle. A common symptom of a failing driveshaft is an intense shaking coming from underneath the vehicle. …
- Difficulty turning. …
- Loud clunking noise. …
- Car shudders upon acceleration. …
- Squeaking noise. …
- Clicking or knocking noise.
How long can you drive with a bad drive shaft?
If you allow the driveshaft to die completely, then it will reach the point where the wheels no longer receive any power. While there is no set lifespan of a driveshaft, it typically can
last about 75,000 miles
. Keep in mind depending on the vehicle, and wear and tear you may get much less or much more.
What causes a broken drive shaft?
Worn out u-joints or bushings
can cause the driveshaft to vibrate. If you don’t get the u-joints or bushings serviced, it can lead to further damage to other drivetrain components. … Vibrations caused by tire balance issues are speed sensitive while driveshaft vibrations aren’t.
Can you drive without a drive shaft?
You can drive the vehicle indefinitely in this mode with one driveshaft removed.
Never drive
with one driveshaft removed unless the CDL is locked; you can burn up the viscous coupler in vehicles so equiped, but also the vehicle will roll even if the transmission is Park (unless the Emergency brake is engaged).
Should I mark drive shaft before removal?
It’s balance
so it shouldn’t matter how it comes out and goes back in unless you take the actuall driveshaft apart. Then you would need to mark the yokes so you could put those back in the same way they came out.
Does it matter which way a drive shaft goes?
Actually,
it does matter which way the yokes are installed
, and 90 degrees is not the way to go. Correctly oriented universal joints are said to be in phase (as illustrated below).
How do you balance a drive shaft?
To field balance a driveshaft,
raise vehicle parallel to the ground so that the vehicle can be started and the tires and wheels can rotate freely
. Measure about six inches from the yoke end, and place four marks 90 degrees apart around the driveshaft. Number them so that they can be identified.
